Bedienungsanleitung Bosch TR1000 12 B (Seite 8 von 40) (Deutsch, Englisch, Holländisch, Französisch)

697132

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Installation instructions

TR1000 12 B – 6 720 876 017 (2019/06)

CAUTION:

Earthed water pipes may give the appearance of a

connected protective earth.

• To guarantee compliance to relevant safety

regulations, an all-pole separator must be fitted

during installation, according to chapter 3. The

contact opening must be at least 3 mm.

• This appliance can be installed with three (3)

different configurations corresponding to three(3)

rated power values ( chapter 2).

• Ensure that the inlet water pressure, maximum and

minimum, is according with the value specified by

the manufacturer ( chapter 3).

• The water inlet of this appliance shall not be

connected to inlet water obtained from any water

heating system.

• The continuous-flow heater is only suitable for

closed (pressurised) operation.

• The tap and outlet fittings must be approved for

operation with closed (pressurised) continuous-

flow heater systems.

• Only connect the continuous-flow heater to a cold

water line. A non-return valve must NOT be

connected to the cold water.

• Do not use plastic pipes. Steel or copper pipes are

suitable for the cold-water supply. Insulated copper

pipes are particularly suitable for the hot-water

pipes.

• The appliance is suitable for supplying water for

multiple points of use, including showers.

• The appliance should be installed close to the

tap that is used the most frequently.

• Disconnect the electrical connection cable from

the supply and shut off the water supply before

connecting the appliance!

• Connect the water supply and then connect the

electrical supply.

• Only make the openings which are required for

installation on the rear of the appliance. If the

appliance is reinstalled, the unused openings must

be provided with watertight sealing.

• Do not touch electrically live parts after installation.

• The appliance should be disconnected from the

electrical mains supply when working on the water

supply. After service work is complete, proceed as

during the first-time appliance start-up.

• No changes may be made to the appliance.

• The appliance may only be used for heating drinking

water for household use.

• The mixer and the warm water pipe may be hot.

• Do not use aggressive or abrasive cleaning

detergents!

• Do not use a steam cleaner.

• The appliance is only to be descaled by a suitably

qualified specialist.

Safety of electrical devices for domestic use and

similar purposes

The following requirements apply in accordance with

EN 60335-2-35 in order to prevent hazards from

occurring when using electrical appliances:

“This appliance can be used by children of 3 years and

older, as well as by people with reduced physical,

sensory or mental capabilities or lacking in experience

and knowledge, if they are supervised and have been

given instruction in the safe use of the appliance and

understand the resulting dangers. Children shall not

play with the appliance. Cleaning and user

maintenance must not be performed by children

without supervision.”

“If the power cable is damaged, it must be replaced by

the manufacturer, its customer service department or

a similarly qualified person, so that risks are avoided.”

Please read this installation and operating

instruction manual carefully, then act accordingly!

Store for future reference.

Congratulations on purchasing this BOSCH appliance.

You have acquired a top-quality product, which will

give you a lot of enjoyment.

2 Installation instructions

Install the continuous-flow heater as described in the illustrated

section. Observe the instructions in the text.

The illustrations can be found in the centre of the instruction manual.

2.1 Installation

I. List of items supplied

1. Continuous-flow heater

2. Installation template

3. Connection piece for hot water

4. Washer, red Ø 15 mm

5. Connection piece for cold water

6. Washer, Ø 24 mm

7. Mounting bolt

8. Wall plug

9. Securing nut

10.Threaded bushing

11.Cable grommet

II. Wall mounting

There are two ways in which the continuous-flow heater can be mounted

on the wall:

• Using the mounting bolt. Unevenness in the wall up to a depth

of 25 mm can be compensated for.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch TR1000 12 B Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info