Bedienungsanleitung Bosch Tronic 2000 - 12 (Seite 8 von 92) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Polnisch)

697121

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

Installation instructions

TR2000 | TR2000R – 6 720 876 014 (2019/09)

• Connect the water supply and then connect the

electrical supply.

• Only make the openings which are required for

installation on the rear of the appliance. If the

appliance is reinstalled, the unused openings must

be provided with watertight sealing.

• Do not touch electrically live parts after installation.

• The appliance should be disconnected from the

electrical mains supply when working on the water

supply. After service work is complete, proceed as

during the first-time appliance start-up.

• No changes may be made to the appliance.

• The appliance may only be used for heating drinking

water for household use.

• The mixer and the warm water pipe may be hot.

Please inform and instruct children appropriately.

• Do not use aggressive or abrasive cleaning

detergents!

• Do not use a steam cleaner.

• The appliance is only to be descaled by a suitably

qualified specialist.

Safety of electrical devices for domestic use and

similar purposes

The following requirements apply in accordance with

EN 60335-2-35 in order to prevent hazards from

occurring when using electrical appliances:

“This appliance can be used by children of 3 years and

older, as well as by people with reduced physical,

sensory or mental capabilities or lacking in experience

and knowledge, if they are supervised and have been

given instruction in the safe use of the appliance and

understand the resulting dangers. Children shall not

play with the appliance. Cleaning and user

maintenance must not be performed by children

without supervision.”

“If the power cable is damaged, it must be replaced by

the manufacturer, its customer service department or

a similarly qualified person, so that risks are avoided.”

Congratulations on purchasing this BOSCH appliance.

You have acquired a top-quality product, which will

give you a lot of enjoyment.

Please read this installation and operating

instruction manual carefully, then act accordingly!

Store for future reference.

2 Installation instructions

Install the continuous-flow heater as described in the illustrated

section. Observe the instructions in the text.

2.1 Installation

Unpacking/removing the cover (Fig. 1)

• Unpack the appliance and check for transport damage.

• Dispose of the packaging and, where applicable, the old appliance, in

an environmentally conscious manner.

Preparation for installation (Fig. 2)

Important: Only use the enclosed installation set.

• Shut off water supply. The electrical connection (connection cable)

must be disconnected from the power supply. Unscrew the fuse or

switch off the circuit breaker.

Wall mounting (Fig. 3)

• The continuous-flow heater must be fitted securely to the wall.

If required, secure the appliance using the lower adjusting screws.

• The distance from the wall is variable. This allows you to compensate

for any unevenness in the wall surface.

• The sleeve must fit tightly round the connection cable. If the sleeve is

damaged during installation, the holes must be sealed water-tight.

Water connection (Fig. 4)

• The continuous-flow heater must be vented. Open the warm water

tap fully and flush out the appliance thoroughly for 1 minute.

• The flow-rate limiter must be installed in the old water regulating

valve.

In accordance with EN60335-2-35, when the appliance is intended to

supply water for showering, the flow limiter must not be installed

(Fig. 6[A]).

Electrical connection (Fig. 5)

• The electrical supply terminal can be fitted at the top or bottom.

The sheath of the connection cable must extend for at least 40 mm

into the appliance.

Installation note

• The installation of non plug-in ready appliances must be undertaken

by the respective utility operator or by a qualified specialist company,

who can also assist you when you are requesting the approval of

the utility company for installation of the appliance.

Startup (Fig. 6/7)

The device is compliant to IEC 61000-3-12.

• At low water pipe pressure, check whether the 2 setting switches

on even when water is drawn from several cold-water taps

simultaneously. If not, remove the flow limiter (refer to additional

information 6,A).

• Instruct the user with regard to the operation of the continuous-flow

heater.

Additional information (Fig. 6, A/B)

• If the water pressure of the interior system is low, do not operate

the continuous-flow heater at full power, but remove the flow limiter

(A, 3).

• Priority circuit for the combined operation of electric storage heaters

(B).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch Tronic 2000 - 12 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info