Bedienungsanleitung Bosch Tronic 4000 - 18 (Seite 6 von 36) (Deutsch, Englisch, Holländisch, Französisch, Polnisch, Türkisch)

697117

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Operating instructions

6 720 876 041 (2019/10)

Congratulations on purchasing this BOSCH appliance.

You have acquired a top-quality product, which will

give you a lot of enjoyment.

2 Operating instructions

2.1 Getting to know your appliance

This appliance is an electronically-regulated, pressurized continuous-

flow heater for decentrally supplying hot water.

The electronic continuous-flow heater heats the water as it flows through

the appliance. One or more taps can be supplied with warm water.

2.1.1 Operating element

1 Status display

2.2 Operating the appliance

2.2.1 Switching the appliance on and off

The continuous-flow heater switches on and heats the water when

the warm water tap is opened. It switches off again if the water tap

is closed.

The factory default setting for the warm water outflow temperature

is 55 °C.

Note: The electronic control unit senses the input water’s temperature

and rate of flow and automatically adjusts the power consumption in

order to obtain the set output water temperature (up to the power limit).

Increasing the water temperature

If the supply water temperature is low and the flow-rate is high, then it

may happen that the set output water temperature is not obtained

because the power limit is exceeded. This is signalled by rapid flashing of

the status display.

• If this happens, then slightly close the warm water tap.

2.2.2 Status display

2.2.3 Startup after power failure

• Open the warm water tap fully and allow water to flow until it is warm.

2.2.4 Using the appliance after switching off the water supply

• Switch off the appliance (unscrew the fuse in the fusebox).

• Open the warm water tap and keep it open until the air has been

completely forced out of the water pipe.

• Switch the fuse back on again.

• Open the warm water tap fully and allow water to flow for at least one

minute.

Only then (for safety reasons) will the appliance begin to heat.

The appliance is now ready to operate.

2.2.5 Winter operation

Note: It is possible in winter that the supply temperature of the water is

reduced and the required outlet temperature is no longer achieved.

• Reduce the water flow at the tap until the desired water temperature

is reached.

3 Cleaning

• Only wipe off the appliance using a moist cloth.

• Do not use acidic or abrasive cleaning materials.

• Do not use a steam cleaner.

4 Customer Service

We ask you to always provide the BOSCH serial number (SNR/TTNR) of

your appliance when calling in a customer service engineer. You will find

the numbers on the ratings plate on the inner side of the front flap.

LED Appliance status

Off Off

Lights green On

Flashes green (1/s) The set temperature is not obtained; the rate of

water flow is too high for appliance rating

(the appliance has reached the power limit).

See “A fault, what to do?”

Flashes green (2/s) Cold-water rinse-through phase

Flashes red See “A fault, what to do?”

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch Tronic 4000 - 18 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info