Bedienungsanleitung Bosch Tronic 7000 - 21-24 (Seite 9 von 40) (Deutsch, Englisch, Holländisch, Französisch, Polnisch, Türkisch)

697112

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

A fault, what to do?

6 720 876 024 (2018/09)

3 A fault, what to do?

CAUTION:

Attention!

▶ Repairs must only be carried out by an authorised technician.

Improper repairs can lead to risk of serious injury to the user.

If your appliance does not operate as required, it is often due to a very

minor problem. Please check whether you can remedy the fault yourself

by using the following guidelines. You will save yourself the costs of an

unnecessary visit by customer service personnel.

3.1 Faults that the customer can troubleshoot himself

If the fault could not be eliminated, please call customer service.

3.2 Faults that the customer service specialist should troubleshoot

3.3 Faults that are automatically remedied

4 Guarantee

The guarantee conditions for this appliance are as defined by our

representative in the country in which it is sold.

Details regarding these conditions can be obtained from the dealer from

whom the appliance was purchased. The bill of sale or receipt must

be produced when making any claim under the terms of this guarantee.

Subject to change without notice.

Fault Cause Solution

Water flow-rate is too low. The filter in either the water tap or the

showerhead is clogged.

Remove the filter and either clean it or descale it.

A high water temperature is set, but it is not

reached.

The continuous-flow heater is connected to a

thermostatically-controlled water tap.

Set the temperature on the continuous-flow

heater to „60 °C“.

The display is blank. The fuse in the fusebox has tripped/blown. Check the fuse in the fusebox.

The water is not warm. The supply temperature has reduced. Reduce the water flow on the taps until the

desired water temperature is reached.

The temperature of the water leaving the tap is

higher than the set temperature.

The temperature of the water supplying the

continuous-flow heater is higher than the set

temperature (e. g. due to pre-warmed water

supplied from a solar water heater).

The thermostatic premixer in the domestic

supply must be set accordingly to lower

temperatures.

“°C” flashes in the display. The power limit has been reached. Reduce the water flow at the tap or lower the

temperature setting on the appliance.

Fault Cause Solution

Water flow-rate is too low despite cleaning of

filter using the water tap or showerhead.

A filter in the appliance is clogged. Get a servicing expert to clean the appliance.

The display is blank despite fault-free function of

the mains electricity supply fuses.

There is a fault in the appliance. Get a servicing expert to check the appliance.

The display shows the error code “E..”. There is a fault in the appliance. Get a servicing expert to check the appliance.

Fault Cause Solution

The display shows “00,0°C”. The air sensor in the appliance detects air in the

water and momentarily switches the heating

element off.

After a few seconds, the continuous-flow heater

automatically goes back into operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch Tronic 7000 - 21-24 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info