Bedienungsanleitung Bosch TW 2 (Seite 9 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch)

458023

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

TW2

English

The TW 2 remote control has the following con-

trol elements (Fig. ):

e Operational mode switch

f Adjustment knob

g Brief operating instructions:

In the compartment on the right side of

the base, a small instruction manual

can be found. It contains all essentials

for operation in brief form.

h Switch (Fig. )

5.1 Operating Mode Switch (e)

With this switch, selection can be made be-

tween the following four different operating

modes:

Frost Protection Operation:

• At outside temperatures above + 4 °C,

the central heating appliance is

switched off (burner and pump).

If a mixer valve is fitted, it closes and the

circulation pump for that circuit is

switched off.

• At outside temperatures below +3 °C,

the central heating appliance is adjusted

to the minimum temperature set on the

outside-temperature controlled pro-

grammer. In case a heating mixer is

present, it regulates to a feed tempera-

ture for +10 °C and the circulation pump

for this heating circuit runs.

Central Heating Mode:

Continuous regulation of the temperature

to the value set on the knob (f). See

“Temperature Range” for the temperature

range.

Economy Mode: Continuous reduction

of the temperature

• Room thermostat function off:

If the control knob (f) is in the centre po-

sition, the central heating flow tempera-

ture is reduced by approx. 25 K com-

pared with the set heating characteristic.

• Room thermostat function on:

If the control knob (f) is in the centre po-

sition, the central heating flow tempera-

ture is reduced by approx. 3 K compared

with the set heating characteristic.

The reduced temperature setting on the out-

side-temperature controlled programmer has no

effect. The circulation pump is switched on.

Alternating mode:

Temperature control alternates automati-

cally between central heating and economy

modes or between central heating and anti-

freeze modes.

Alternation takes place according to the

mode selected ( or Automatic) on the

outside-temperature controlled program-

mer or the timer program setting.

5.2 Knob (f)

The control knob shifts the heating characteris-

tic set on the outside-temperature controlled

programmer up or down.

– Set the central heating flow temperature on

the control knob.

A division corresponds to a change of the

feed temperature of 4 K and therefore a room

temperature change of approx. 0.5 K (see

“Temperature Range”).

5.3 Switch (h)

– After removing the top part of the remote

control (a) from the base (b), the switch (h) is

accessible on the back side of the top part.

– With this switch, the room temperature sens-

ing is switched on or off.

• Position

O = Operation without room

temperature sensing (de-

livered condition)

• Position

● = Operation with room tem-

perature sensing.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch TW 2 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch TW 2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info