Bedienungsanleitung Bosch uneo (Seite 20 von 130) (Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

388878

Zoom out

Zoom in

Vorherige Seite

1/130

Nächste Seite

20 | English

2 609 003 546 | (18.11.10) Bosch Power Tools

The battery is equipped with a NTC temperature

control which allows charging only within a tem-

perature range of between 0 °C and 45 °C. A

long battery service life is achieved in this man-

ner.

When the battery charge-control indicator 5

lights up red for approx. 5 seconds with the

On/Off switch 9 pressed through halfway or

fully, then the battery has less than 30% of its

capacity and should be charged.

The charging procedure begins as soon as the

mains plug of the battery charger is plugged into

a socket outlet and the charge connector 17 is

plugged into the socket 16 on the bottom of the

handle.

The battery charge-control indicator 5 indicates

the charging progress. During the charging proc-

ess, the indicator flashes green. When the bat-

tery charge-control indicator 5 lights up green

continuously, the battery is fully charged.

During the charging procedure, the handle of

the machine warms up. This is normal.

Disconnect the battery charger from the mains

supply when not using it for longer periods.

The power tool cannot be used during the

charge procedure; it is not defective when inop-

erative during the charging procedure.

f Protect the battery charger against mois-

ture!

Observe the notes for disposal.

Selecting Tools

For hammer drilling, SDS-Quick tools are re-

quired.

For drilling without impact in wood, metal, ce-

ramic and plastic, a suitable SDS-Quick tool or

an application tool with hexagon shank can be

used.

For screwdriving, use only screwdriver bits with

ball catch 12 (DIN 3126-E6.3). Other screwdriv-

er bits 11 can be inserted via a universal bit

holder with ball catch 10.

A selection of suitable application tools can be

found in the Accessories Overview at the end of

these instructions.

Changing the Tool

The SDS-Quick tool holder allows

for simple and convenient changing

of drilling tools without the use of

additional tools.

Due to their working principle, SDS-Quick drill-

ing tools move freely. This results in radial run-

out at no-load. However, this has no effect on

the accuracy of the drill hole, as the drill bit cen-

tres itself during drilling.

The SDS-Quick tool holder can also accommo-

date different drill-bit types with hexagon

shank. For more information, see the accesso-

ries page at the end of these operating instruc-

tions.

The dust protection cap 2 largely prevents the

entry of drilling dust into the tool holder during

operation. When inserting the tool, take care

that the dust protection cap 2 is not damaged.

f A damaged dust protection cap should be

changed immediately. We recommend hav-

ing this carried out by an after-sales serv-

ice.

Inserting SDS-Quick Drilling Tools

(see figure B)

Clean and lightly grease the shank end of the

tool.

Insert the tool in a twisting manner into the tool

holder until it latches itself.

Check the latching by pulling the tool.

Removing SDS-Quick Drilling Tools

(see figure C)

Push back the locking sleeve 3 and remove the

tool.

Dust/Chip Extraction

f Dusts from materials such as lead-containing

coatings, some wood types, minerals and

metal can be harmful to one’s health. Touch-

ing or breathing-in the dusts can cause aller-

gic reactions and/or lead to respiratory infec-

tions of the user or bystanders.

OBJ_BUCH-605-004.book Page 20 Thursday, November 18, 2010 2:35 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch uneo Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info