Bedienungsanleitung Bosch UniversalAquatak 130 (Seite 12 von 290) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

708251

Zoom out

Zoom in

Vorherige Seite

1/290

Nächste Seite

12 | English

F 016 L81 568 | (26.4.17) Bosch Power Tools

Connecting to the mains

The voltage indicated on the rating

plate must correspond to the voltage

of the power source.

We recommend that this equipment

is only connected into a socket which

is protected by a circuit-breaker that

would be actuated by a 30 mA residu-

al current.

Remove the plug from socket when-

ever the machine is left unattended

for any period.

The electric supply installation

should comply with IEC 60364-1.

If the supply cord is damaged, it must

be replaced by the manufacturer, its

service agent or similarly qualified

persons in order to avoid a hazard.

If the plug is damaged, pay attention

to the following:

Plugs and sockets situated near the

work site or outdoors should be to

class IP 55 of BS 5490 to provide ad-

equate protection against ingress of

water, etc. and cable entries require

effective sealing. Rubber shrouds

should be provided over cable

glands. Drip-proof (class IP X2 of

BS 5490) plugs and sockets to

BS 4343 are suitable for use indoors

where the plug is away from the water

spray area where the appliance is in

use.

Never touch the mains plug with wet

hands.

Do not pull plug while operating the

device.

Do not run over, crush or pull the

power supply cord or extension cord,

otherwise it may be damaged. Pro-

tect the cable from heat, oil and sharp

edges.

Do not use the unit, if the power sup-

ply cord or important parts, e. g.

high-pressure hose, power gun or

safety devices are damaged.

Warning: Inadequate extension cords

can be dangerous.

If an extension cord is used, the plug

and socket must be of watertight con-

struction. The extension cord must

have a cross section in accordance

with the operating instructions and

be protected against splashed water.

The connection must not be in water.

When replacing plugs on the power

supply cable or extension lead the

spray water guard and mechanical

stability must remain intact.

Water connection

Comply with the regulations of your

water supply company.

All connecting hoses must have prop-

erly sealed joints.

Make sure that the supply hose is at

least 12.7 mm (1/2") in diameter and

is reinforced.

The appliance should never be used

on the drinking water supply without

a back flow valve. Water which has

passed the back flow valve is regard-

ed as undrinkable.

The high-pressure hose must not be

damaged (danger of bursting). A

damaged high-pressure hose must be

replaced immediately. Only use hos-

es and connections recommended by

the manufacturer.

OBJ_BUCH-2981-002.book Page 12 Wednesday, April 26, 2017 3:49 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch UniversalAquatak 130 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info