Bedienungsanleitung Bosch UniversalAquatak 130 (Seite 16 von 290) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

708251

Zoom out

Zoom in

Vorherige Seite

1/290

Nächste Seite

16 | English

F 016 L81 568 | (26.4.17) Bosch Power Tools

Mounting and Operation

Starting

Electrical Safety

Warning! Switch off, remove plug from mains

before adjusting, cleaning or if cable is cut,

damaged or entangled.

Your machine is double insulated for safety and requires no

earth connection. The operating voltage is 230 V AC, 50 Hz

(for non-EU countries 220 V, 240 V as applicable).

For increased electrical safety use a Residual Current Device

(RCD) with a tripping current of not more than 30 mA. Always

check your RCD every time you use it.

The supply cables must be inspected for signs of damage at

regular intervals and may only be used if in perfect condition.

If the replacement of the supply cord is necessary, this has to

be done by Bosch or an authorized Bosch service agent in or-

der to avoid a safety hazard.

Only use approved extension cables.

WARNING! Inadequate extension cables can

be dangerous. Extension cable, plug and sock-

et must be of watertight construction and in-

tended for outdoor use.

Extension cords, cables, leads, reels should only be used if

they comply with EN 61242/IEC 61242 or

IEC 60884-2-7.

If you want to use an extension cable when operating your

product, only the following cable dimensions should be used:

– Nominal Conductor Area of 1.5mm

to a max. cable length

of 20m for a Cord Extension Set

The connections (plugs and sockets) should be kept dry and

off the ground.

It is recommended that this is accomplished by means of a

cord reel which keeps the socket at least 60 mm above the

ground.

Note: If an extension cable is used it must be earthed and con-

nected through the plug to the earth cable of your supply net-

work in accordance with prescribed safety regulations.

Refer to the instruction manual of the extension cord, lead,

reel manufacturer and your local wiring regulations.

If in doubt contact a qualified electrician or the nearest Bosch

Service Centre.

For products not sold in GB:

WARNING: For your safety, it is required that the plug at-

tached to the product is connected with the extension cord.

The coupling of the extension cord must be protected against

splash water, be made of rubber or coated with rubber. The

extension cord must be used with a cable strain relief.

 Products sold in GB only: Your product is fitted with a

BS 1363/A approved electric plug with internal fuse

(ASTA approved to BS 1362).

If the plug is not suitable for your socket outlets, it should

be cut off and an appropriate plug fitted in its place by an

authorised customer service agent. The replacement plug

should have the same fuse rating as the original plug.

The severed plug must be disposed of to avoid a possible

shock hazard and should never be inserted into a mains

socket elsewhere.

Products sold in AUS and NZ only: Use a residual current

device (RCD) with a rated residual current of 30 mA or

less.

Operation

Starting

Attach water supply hose (not supplied) to the mains water

supply and machine.

Connect the product to the mains supply ensuring that the

mains switch is in the off position.

Open water tap.

Press the safety lock (back button on the gun handle) to re-

lease the trigger. Fully press the trigger until there is a con-

stant flow of water to clear the air from the machine and water

supply hose. Release trigger. Press the safety lock (front but-

ton on the gun handle).

Turn button on main switch. Point the power gun downwards.

Press the trigger safety lock to release the trigger. Fully press

the trigger.

Autostop function

The machine is designed to switch off the motor when the trig-

ger is released on the gun.

Action Figure Page

Delivery Scope

1 272

Fold down handle operation

2 273

Adjusting the Handle

3 273

Connecting to the water supply

4 274

Connecting/Disconnecting high

pressure gun to lance

5 274

Connecting high pressure water supply

hose/nozzle 6 275

Disconnecting high pressure water

supply hose/nozzle

7 275

Switching On and Off

8 276

Attaching Nozzles

Adjust water jet

9–10 277–278

Connect detergent bottle

11 279

Clean nozzle

12 280

Clean the water filter

13 280

Hose into the hose holder

14 281

Storage

15 281

Gun/lance/nozzle is stored in action

16 281

Selecting Accessories

17 282

OBJ_BUCH-2981-002.book Page 16 Wednesday, April 26, 2017 3:49 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch UniversalAquatak 130 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info