Bedienungsanleitung Bosch UniversalAquatak 135 (Seite 17 von 290) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

708252

Zoom out

Zoom in

Vorherige Seite

1/290

Nächste Seite

English | 17

Bosch Power Tools F 016 L81 568 | (26.4.17)

Working Advice

General

Ensure that the pressure washer is on level ground.

Do not overreach with the high pressure hose or move the

pressure washer by pulling the hose, this could cause the ma-

chine to become unstable and fall over.

Do not kink or drive a motor vehicle over the high pressure

hose. Do not expose the high pressure hose to sharp edges or

corners.

 Never use a roto nozzle or pencil jet to clean motor vehi-

cles.

Working advice for cleaning with detergents

 Only use cleaning agents suitable specifically for high

pressure washers.

We recommend that you use detergent sparingly for the sake

of the environment. Observe the recommended dilution on

the detergent label.

The high-pressure foam nozzle supplied with this product in-

cludes a regulator to control detergent use. Adjust as re-

quired.

Recommended cleaning method

Step 1: Select the fan jet setting on the 3 in 1 nozzle and re-

move the heavy dirt.

Step 2: Attach the foam bottle and spray on the detergent

sparingly.

Step 3: Rinse off the loosened dirt and detergent using the

fan jet setting on the 3 in 1 nozzle.

Note: When cleaning vertical surfaces, apply the detergent

from bottom to top. When rinsing off, work from top to bot-

tom.

Use with alternative water sources

The power washer is self-priming and enables water to be

drawn in from containers or natural water sources. It is IM-

PORTANT that the water filter is in clean condition when in-

serting it at the water inlet, and that only clean water is drawn

in.

Open tanks/containers and natural water sources

Use the Self Priming accessory kit comprising:

– Inlet strainer with non return valve

–3m reinforced supply hose

– Universal coupling to the pressure washer

This enables the pressure washer to draw water up to 0.5 m

above the water level in the source in approximately 15 sec-

onds.

Fully immerse the 3 m hose into the water to displace the air

in the hose. Connect the 3 m hose to the power washer and

make sure that the inlet strainer remains under water.

With the spray gun removed, switch the power washer on and

operate it until water flows uniformly out of the high-pressure

hose. If no water is coming out of the high-pressure hose after

25 seconds, switch the power washer off and check all con-

nections. As soon as water flows out of the high-pressure

hose, switch the power washer off and connect the spray gu-

nand spray lance to begin with the work.

It is important that hose and couplings are of good quality and

are tightly connected, and that the seals are undamaged and

properly inserted. Loose connections can impede the priming

(drawing in).

Water Tanks with outlet connections

When connecting the pressure washer to a water tank with a

suitable tap outlet, first connect the supply hose (not provid-

ed) to the tank outlet, open the tap to allow the water to dis-

place all the air in the hose and then connect to the pressure

washer.

Troubleshooting

Problem Possible Cause Corrective Action

Motor refuses to start Plug not connected Connect plug

Mains socket faulty Use another socket

Fuse faulty/blown Replace fuse

Extension cable damaged Try without extension cable

Motor protector has activated Allow to cool for 15 minutes

Frozen Wait for pump/water supply hose/accessory to

thaw

Motor stops Fuse faulty/blown Replace fuse

Motor protector has activated Allow to cool for 15 minutes

Wrong mains voltage Check that mains voltage corresponds to specifica-

tions on the model tag

Fuses blow Fuses incorrectly rated Change to a mains supply higher than the pressure

washer amp consumption

Motor starts but no pressure Nozzle partly blocked Clean nozzle

OBJ_BUCH-2981-002.book Page 17 Wednesday, April 26, 2017 3:49 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch UniversalAquatak 135 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info