Bedienungsanleitung Bosch UniversalDrill 18V systembox (Seite 17 von 213) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

766881

Zoom out

Zoom in

Vorherige Seite

1/213

Nächste Seite

English | 17

Switching on/off

To start the power tool, press and hold the on/off switch

(10).

The LED (8) lights up when the on/off switch (10) is lightly

or fully pressed, meaning that the work area is illuminated in

poor lighting conditions.

To switch off the power tool, release the on/off switch (10).

Adjusting the Speed

You can adjust the speed of the power tool when it is on by

pressing in the on/off switch (10) to varying extents.

A light pressure on the on/off switch (10) results in a low ro-

tational speed. Increased pressure on the switch causes an

increase in speed.

Preselecting the Torque

The torque presetting ring (3) can be used to preselect the

required torque in 20 stages. When the correct setting is

used, the application tool will be stopped when the screw is

driven flush into the material or once the set torque has been

reached. In position the overload clutch is deactivated,

e.g. for drilling.

When unscrewing screws, you can select a higher setting or

set the tool to the symbol.

Mechanical Gear Selection

uYou can press the gear selector switch (5) with the

power tool off or on. You should not do this at full load

or maximum torque, however.

Gear I:

Low speed range; for working with a large drilling diameter

or for screwdriving.

Gear II:

High speed range; for working with a small drilling diameter.

Setting the operating mode

Screwdriving

UniversalDrill18V

Set the torque presetting ring(3) to the re-

quired torque.

UniversalImpact18V

Set the operating mode presetting ring(4) to

the "screwdriving" symbol.

Set the torque presetting ring(3) to the re-

quired torque.

Drilling

UniversalDrill18V

Set the torque presetting ring(3) to the

"drilling" symbol.

UniversalImpact18V

Set the operating mode presetting ring(4) to

the "drilling" symbol.

Impact drilling

UniversalImpact18V

Set the operating mode presetting ring(4) to

the "impact drilling" symbol.

Fully automatic spindle lock (Auto-Lock)

The drill spindle, and therefore the tool holder(1), are

locked when the on/off switch (10) is not pressed.

This enables screws to be screwed in even when the battery

(7) is empty and allows the power tool to be used as a

screwdriver.

Temperature-dependent overload protection

In normal conditions of use, the power tool cannot be over-

loaded. If the power tool is overloaded or the permitted bat-

tery temperature is exceeded, the electronics of the power

tool will switch off until the temperature returns to within the

optimum operating temperature range.

Practical advice

uOnly apply the power tool to the screw/nut when the

tool is switched off. Rotating tool inserts can slip off.

After working at a low speed for an extended period, you

should operate the power tool at the maximum speed for ap-

proximately three minutes without load to cool it down.

Maintenance and Service

Maintenance and Cleaning

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

uTo ensure safe and efficient operation, always keep

the power tool and the ventilation slots clean.

After-Sales Service and Application Service

Our after-sales service responds to your questions concern-

ing maintenance and repair of your product as well as spare

parts. You can find explosion drawings and information on

spare parts at: www.bosch-pt.com

The Bosch product use advice team will be happy to help you

with any questions about our products and their accessor-

ies.

In all correspondence and spare parts orders, please always

include the 10‑digit article number given on the nameplate

of the product.

Great Britain

Robert Bosch Ltd. (B.S.C.)

P.O. Box 98

Broadwater Park

North Orbital Road

Denham Uxbridge

UB 9 5HJ

At www.bosch-pt.co.uk you can order spare parts or arrange

Bosch Power Tools 1 609 92A 5UK | (21.09.2020)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch UniversalDrill 18V systembox Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info