Bedienungsanleitung Bosch UniversalImpact 6700 (Seite 20 von 127) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

708163

Zoom out

Zoom in

Vorherige Seite

1/127

Nächste Seite

20 | English

UniversalImpact

800

UniversalImpact

6700

UniversalImpact

7000

UniversalImpact

8000

K m/s

1.5 1.5 1.5 1.5

The vibration level and noise emission value given in these

instructions have been measured in accordance with a

standardised measuring procedure and may be used to com-

pare power tools. They may also be used for a preliminary

estimation of vibration and noise emissions.

The stated vibration level and noise emission value repres-

ent the main applications of the power tool. However, if the

power tool is used for other applications, with different ap-

plication tools or is poorly maintained, the vibration level

and noise emission value may differ. This may significantly

increase the vibration and noise emissions over the total

working period.

To estimate vibration and noise emissions accurately, the

times when the tool is switched off or when it is running but

not actually being used should also be taken into account.

This may significantly reduce vibration and noise emissions

over the total working period.

Implement additional safety measures to protect the oper-

ator from the effects of vibration, such as servicing the

power tool and application tools, keeping their hands warm,

and organising workflows correctly.

Assembly

u Pull the plug out of the socket before carrying out any

work on the power tool.

Auxiliary Handle (seefigureA)

u Before carrying out any work, make sure that the wing

bolt is tightened. Loss of control can cause personal in-

jury.

u Do not operate your power tool without the auxiliary

handle (20).

Turn the wing bolt (21) anti-clockwise and guide the auxili-

ary handle (9) in the required position over the drill chuck

onto the spindle collar of the power tool.

You can swivel the auxiliary handle (20) in order to achieve a

safe work posture that minimises your fatigue.

Swivel the auxiliary handle (20) to the required position and

retighten the wing bolt (21) in clockwise direction.

Setting the Drilling Depth (seefigureB)

You can use the depth stop(23) to set the required drilling

depth X.

Press the button for depth stop adjustment (22) and insert

the depth stop into the auxiliary handle (9).

The fluting on the depth stop (23) must face downwards.

Pull the depth stop far enough out that the distance between

the drill bit tip and the edge of the depth stop corresponds

to the required drilling depth X.

Drill Assistant

Applying the Drill Assistant (seefiguresC–D)

The Drill Assistant(10) can be used with and without the

dust collection device(13). Use of the dust collection

device(13) is limited to drill bits with a diameter of 12 mm

and a length of 120 mm.

Attach the dust collection device(13) to the adapter(26).

Press the unlocking button(8) to release the Drill Assist-

ant(10) from its parked position.

Guide the Drill Assistant(10) over the drill chuck onto the

spindle collar of the power tool.

Lock it by turning the wing bolt(18) clockwise.

Setting the Drilling Depth (seefiguresE–F)

Attach the drill bit (see section "Changing the Tool").

You can use the setting ring(17) to set the required drilling

depthX.

Unlock the setting ring(17) by turning it to the left .

Place the dust container(11) or the adapter(26) flush

against the wall or workpiece. Move the tip of the drill bit to

the wall or workpiece.

Slide the setting ring(17) backwards until the distance

matches the required drilling depthX or place a wall plug on

the rail and slide the setting ring(17) backwards to the wall

plug. Lock the setting ring(17) by turning it to the right .

Take the wall plug out of the rail again. The drilling depth now

matches the set length X on the rail.

Note: It is important to have the exact drilling depth when

using wall plugs. If the drilled hole is too deep, the wall plug

will slip too far into the wall or workpiece. If the hole is too

small, the wall plug will stick out.

Emptying the dust container (see figure G)

The dust container(11) is enough for drilling about 25 holes

in masonry at a drilling depth of 30 mm with a drill bit dia-

meter of 6 mm.

To remove the dust container(11), press the side-mounted

unlocking buttons(12) and pull the dust container off down-

wards.

Empty the dust container(11) and reinsert it (until it can be

heard to engage).

Removing the Drill Assistant

Press and hold the clip(16) of the dust collection

device(13) and pull the dust collection device(13) off to-

wards the front.

Turn the wing bolt(18) anticlockwise until the auxiliary

handle(9) can be moved and pull the auxiliary handle(9) off

the power tool.

Unlock the setting ring(17) by turning it to the left .

Hold the auxiliary handle(9) in place and slide the rail to-

wards the auxiliary handle until it can be heard to engage.

1 609 92A 57D | (29.11.2019) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch UniversalImpact 6700 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info