Bedienungsanleitung Bosch UniversalImpact 700 plus Drill Assistant (Seite 21 von 127) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

708160

Zoom out

Zoom in

Vorherige Seite

1/127

Nächste Seite

English | 21

Dust Extraction/Dust Container

The dust from materials such as lead paint, some types of

wood, minerals and metal can be harmful to human health.

Touching or breathing in this dust can trigger allergic reac-

tions and/or cause respiratory illnesses in the user or in

people in the near vicinity.

Certain dusts, such as oak or beech dust, are classified as

carcinogenic, especially in conjunction with wood treatment

additives (chromate, wood preservative). Materials contain-

ing asbestos may only be machined by specialists.

– Use a dust extraction system that is suitable for the ma-

terial wherever possible.

– Provide good ventilation at the workplace.

– It is advisable to wear a P2 filter class breathing mask.

The regulations on the material being machined that apply in

the country of use must be observed.

u Avoid dust accumulation at the workplace. Dust can

easily ignite.

u Use the dust box only when working on concrete and

stone. Wood chips and plastic chips can easily lead to

clogging.

u Warning: Danger of fire! Do not work on any metallic

materials with the dust container mounted. Hot metal

chips can ignite parts of the dust container.

Please observe the following instructions to optimise your

use of the dust container:

– Ensure that the dust container is placed flush against the

workpiece or wall. This also makes it easier to drill at a

right angle.

– When you reach the required drilling depth, pull the drill

bit out of the drill hole first and then switch off the impact

drill.

– The dust protection ring(15) can wear, especially when

working with large drill-bit diameters. Replace the dust

protection ring when worn/damaged.

Changing the Tool

Keyless Chuck (UniversalImpact 700, UniversalImpact

700 + Drill Assistant) (seefigureH)

u Press the spindle lock button(2) only when the ma-

chine is at a standstill.

The drill spindle is locked by pressing the spindle lock but-

ton(2). This makes it possible to change the application tool

in the drill chuck quickly, conveniently and easily.

Open the keyless chuck (1) by turning it in the direction of

rotation  until the tool can be inserted. Insert the tool.

Firmly tighten the sleeve of the keyless chuck (1) by turning

it by hand in the rotational direction  until it stops clicking.

This will automatically lock the drill chuck.

The lock will disengage again if you turn the sleeve in the op-

posite direction to remove the tool with the spindle locking

button pressed.

Keyless Chuck (UniversalImpact 800) (seefigureI)

The drill spindle is locked when the on/off switch (6) is not

pressed. This makes it possible to change the application

tool in the drill chuck quickly, conveniently and easily.

Open the keyless chuck (1) by turning it in the direction of

rotation  until the tool can be inserted. Insert the tool.

Firmly tighten the sleeve of the keyless chuck (1) by turning

it by hand in the rotational direction  until it stops clicking.

This will automatically lock the drill chuck.

The lock will disengage again if you turn the sleeve in the op-

posite direction to remove the tool.

Keyed Chuck (UniversalImpact 650) (seefigureJ)

u Press the spindle lock button(2) only when the ma-

chine is at a standstill.

The drill spindle is locked by pressing the spindle lock but-

ton(2). This makes it possible to change the application tool

in the drill chuck quickly, conveniently and easily.

u Wear protective gloves when changing tools. The drill

chuck may heat up significantly when it is used for long

periods.

Open the keyed chuck (28) by turning it until the tool can be

inserted.

Insert the tool.

Insert the drill chuck key (29) into the corresponding holes

of the keyed chuck (28) and clamp the tool evenly.

Screwdriving tools

You should always use a universal bit holder (24) when using

screwdriver bits (25). Only use screwdriver bits that fit the

screw head.

For screwdriving, make sure the "drilling/impact drilling" se-

lector switch (3) is always set to the "drilling" symbol.

Changing the drill chuck

u Pull the plug out of the socket before carrying out any

work on the power tool.

Removing the Drill Chuck (seefigureK)

Remove the auxiliary handle(9).

Insert a steel pin with a diameter of 4 mm and a length of ap-

prox. 50 mm into the hole on the spindle collar to lock the

drill spindle in place. Clamp a hex key (27) in the keyless

chuck (1), leading with the short shaft.

Place the power tool on a firm surface, e.g. a work bench.

Hold the power tool in place and loosen the keyless chuck

Bosch Power Tools 1 609 92A 57D | (29.11.2019)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch UniversalImpact 700 plus Drill Assistant Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info