Bedienungsanleitung Bosch UniversalMulti 12 Multitool (Seite 20 von 145) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

708268

Zoom out

Zoom in

Vorherige Seite

1/145

Nächste Seite

20 | English

1 609 92A 3AY | (3.3.17) Bosch Power Tools

Note: If the machine should automatically switch off because

of a discharged or overheated battery, make sure to set the

machine’s On/Off switch 2 to off. Charge the battery and

allow it to cool down before restarting the machine. Other-

wise the battery can become damaged.

Removing the battery

To remove the battery 3, press the unlocking buttons 4 and

pull the battery out of the machine to the rear. Do not exert

any force.

Battery Charge-control Indication

When the power tool is switched on, the battery charge-

control indicator 6 signals the still available battery capacity

or an overload.

When the battery charge-control indicator 6 flashes red, the

machine is subject to overload. Please observe the infor-

mation in section “Temperature-dependent Overload Protec-

tion”, page 25.

Changing the Tool

 Before any work on the machine itself (e. g. mainte-

nance, tool change, etc.) as well as during transport

and storage, remove the battery from the power tool.

There is danger of injury when unintentionally actuating

the On/Off switch.

 Wear protective gloves when changing application

tools/accessories. Contact with the application tool/

accessory can lead to injuries.

Please observe the application tools/accessories intended

for your tool.

Selecting the Application Tool/Accessory

The following table shows examples for application tools. Further application tools can be found in the extensive Bosch acces-

sories program.

Indication Capacity

Continuous lighting, green >70 %

Continuous lighting, yellow 30–70 %

Continuous lighting, red <30 %

Accessory UniversalMulti 12

Accessory Material Application

BIM segment saw

blade

Wooden materials,

Plastic,

Non-ferrous metals

Separating and plunge cuts; also for sawing close to edges,

in corners and hard to reach areas;

example: shortening already installed bottom rails or door

hinges, plunge cuts for adjusting floor panels

Base plate for

sanding, series

Delta 93 mm

Depends on sanding sheet Sanding surfaces close to edges, in corners or hard to reach

areas;

depending on the sanding sheet for, e.g., sanding wood,

paint, varnish, stone

Fleeces for cleaning and for texturing wood, removing rust

from metal and for keying varnishes, polishing felt for pre-

polishing

Profile sander

Wood,

Pipes/Profile,

Paint,

Varnishes,

Filler,

Metal

Convenient, efficient sanding of profiles up to a diameter of

55 mm;

Red sanding sheets for sanding wood, pipes/profiles, var-

nishes, fillers and metal

BIM plunge cut

saw blade, wood

and metal

Softwood,

Soft plastics,

Plasterboard,

Thin-walled aluminium

and non-ferrous metal

profiles,

Thin sheet metals,

Non-hardened nails and

screws

Smaller separating and plunge cuts;

example: cutting an opening for sockets, flush cutting a

copper pipe, plunge cuts in plasterboard

Filigree adjustment work in wood;

example: sawing openings for locks and fittings

OBJ_BUCH-2957-001.book Page 20 Friday, March 3, 2017 2:20 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch UniversalMulti 12 Multitool Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info