Bedienungsanleitung Bosch Vero professional (Seite 38 von 132) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

506891

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

deen

Dispensing hot water



! Risk of burns

The milk frother 10 gets very hot. After use,

allow to cool down ﬁrst before touching.

The appliance must be ready for use.

Place the pre-warmed cup or glass under

the outlet of the milk frother 10.

Select the required setting for hot water

by turning the knob 6.

Press the

start

button 8. Hot water runs

out of the milk frother outlet 10 for about

40 seconds.

Press the

start

button 8 again to cut the

process short.

N.B.: It is possible to set the temperature of

the hot water (see “Controls, °

button”).

Maintenance and daily

cleaning



! Risk of electric shock

Unplug the appliance before cleaning it.

Never immerse the appliance in water.

Do not use a steam cleaner.

Wipe the outside of the appliance with a

soft, damp cloth. Do not use abrasive

cloths or cleaning agents.

Rinse the water tank 11 and the brewing

unit 23 with water only.

The cover of the storage compartment

25, the drip tray panel 26 and the cover of

the milk container 31 should only be

wiped gently with a damp cloth. Do not

put them in the dishwasher.

Remove cup stand 28. Pull the drip tray

27 with the coffee grounds container 29

forward and out, then empty and clean

them. All the parts can also be cleaned

in the dishwasher.

Clean the measuring spoon 14, the

aroma cover 16 and the milk container 31

by hand or in the dishwasher.

Wipe out the inside of the appliance (tray

holders).

●

Important:

The drip tray 27 should be

emptied and cleaned daily to prevent mould

from developing.

N.B.: If the appliance is cold when switched

on with the

a button 2, or if it is set to a

mode after brewing coffee, it rinses

automatically, in other words the system

cleans itself.

Cleaning the milk system

Clean the milk system 10 immediately after

use!

The milk system 10 can be pre-cleaned

automatically.

Select the

symbol in the display 5 and

press the

start

button 8.

PLACE EMPTY GLASS UNDER FROTHER,

LACE SUCTION PIPE IN GLASS



START

Place an empty glass under the milk

system 10 and put the end of the pipe

10d in the glass.

Press the

start

button 8. The appliance

now ﬁlls the glass automatically with

water and draws it in again through the

pipe 10d for cleaning. The rinse

procedure stops automatically after about

1 minute.

Now empty the glass and clean the pipe

10d.

In addition to this, clean the milk system

thoroughly at regular intervals (by hand or

in the dishwasher).

Dismantling the milk system 10 for

cleaning:

Pull the milk system 10 forward out of the

appliance.

Clean the individual parts (Fig. C) with a

detergent solution and a soft brush.

Rinse all parts with clear water and dry

them.

Reassemble all the parts and replace fully

in the appliance.

Note: All the parts of the milk frother 10 can

also be put in the dishwasher.

●

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch Vero professional Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch Vero professional

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info