11
What to do if ...
ʑ
Water is leaking out. – Attach/replace the drainage hose correctly.
– Tighten the screw connection of the supply hose.
ʑ
No water supply.
Detergent not dispensed.
– Start/Pause $ not selected?
– Tap not turned on?
– Filter blocked? Clean the filter –> page 10.
– Supply hose kinked or trapped?
ʑ
Washing machine door
cannot be opened.
– Safety function active. Wait approx. 2 minutes.
– Is
XƱƩƘƪ ƌƬƵưƢƥƨ
(Rinse Hold, without final spin) selected?
–> page 3,
4.
ʑ
Programme does not
start.
– Start/Pause $ selected?
– Washing machine door closed?
ʑ
Detergent solution is not
drained.
– Is
XƱƩƘƪ ƌƬƵưƢƥƨ
(Rinse Hold, without final spin) selected?
–> page 3,
4.
– Clean the detergent solution pump –> page 10.
– Clean the waste pipe and/or drainage hose.
ʑ
Water not visible in the
drum.
– Not a fault - water below the visible area.
ʑ
Spin result not
satisfactory.
– Distribute large and small items of laundry evenly in the drum.
– ŻƱƟƤƠƤ ƧƞƙƒƥƭơƖ S (Easy-Iron) selected? –> page 5.
– Too low a speed selected? –> page 5.
ʑ
Spin cycle performed
several times.
– Not a fault - unbalanced load detection system adjusts the
imbalance.
ʑ
Residual water in the
compartment for care
products.
– Not a fault - the action of the care product is not affected.
– Clean the insert if necessary –> page 9.
ʑ
Odour formation in the
washing machine.
– Run programme ŷƢƝƚƟƨƞƟƑ /ƌƥƭơƖƨƞƧƨƑ (Cottons) 90 °C without
laundry. Use standard detergent.
ʑ
Foam escaping from the
detergent drawer.
– Too much detergent used?
If foam is escaping from the detergent drawer:
Mix 1 tablespoon of fabric softener with ½ litre of water and pour
into compartment II (not with outdoor or down fabrics).
– Reduce the detergent dosage for the next wash cycle.
ʑ
Intense noise formation,
vibrations and “walking”
during the spin cycle.
– Are the appliance feet fixed?
Secure the appliance feet –> Installation instructions.
– Transportation safety devices removed?
Remove the transportation safety devices –> Installation
instructions.
ʑ
The indicator lights do
not function during
operation.
– Power cut?
– Fuses tripped? Reset/change the fuse.
– If the fault occurs repeatedly, call the after-sales service.
ʑ
Programme sequence
longer than usual.
– Not a fault - unbalanced load detection system adjusts
imbalance by repeatedly distributing the laundry.
– Not a fault - foam detection system active - adds an additional
rinse cycle.
ʑ
Detergent residues on
the laundry.
– Occasionally, phosphate-free detergents contain water-insoluble
residues.
– Select ƄƒƗƘƖƠơƖ/ƌƬƵưƢƥƨ (Rinse /Spin) or brush out the laundry
after washing.
If you cannot correct a fault yourself (switching on/off) or a repair is required:
– Turn the programme selector to Off and remove the mains plug from the socket.
– Turn off the water supply and call the after-sales service –> Installation instructions.
