Bedienungsanleitung Bose 791 (Seite 6 von 12) (Englisch)

450967

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

EnglishTAB 6TAB 8 TAB 7 TAB 3TAB 5 TAB 2TAB 4

INSTALLATION

Preparing the ceiling

Be sure you have read and understand all of the safety

and preparation information on these pages so you can

continue with confidence.

CAUTIONS:

• If you are unsure of your ability to complete this

process, contact a professional installer.

• Certain forms of insulation (such as horse hair plaster,

newspaper, cellulose, or any blown-in materials) may

pose a risk of ignition. Be sure to keep all insulation

away from speakers in accordance with the installation

instructions.

WARNINGS:

• Make sure the spot chosen is safe for cutting. Do not

cut through surfaces that may have hazards such as

electrical wiring, conduits, or plumbing concealed

behind them. Follow all other safety precautions.

• If you believe there is asbestos insulation in the ceiling

where you want to install a speaker, do not drill or cut

there. Find a different ceiling area for the speakers

instead.

• If there is another type of moveable insulation in the

ceiling, you can proceed after reading these tips:

– You may need to cut or push the insulation away

before inserting the speaker.

– Beware of hidden nails when reaching into the

ceiling to remove insulation.

– Wear gloves and protection for your mouth, nose,

and eyes before handling insulation that contains

fiberglass.

– Be sure keep a 4-6 in. (10-15 cm) area around the

speaker hole free from any types of insulation to

maximize acoustic performance.

Using the template

1. Center the template on the spot where you want the

center of the speaker grille.

2. Press the template to the ceiling with your hand or

use painter’s tape to hold it in place.

3. Trace around the edge of the template.

CAUTION: DO NOT trace around or cut around the tabs

that are for use only when the template serves as a paint

shield.

Drilling a pilot hole

1. Choose the proper spade bit to drill a hole that is

large enough for the blade of your cutting tool.

WARNING: Use eye protection and be sure to observe all

safety precautions while using a drill or cutting tool.

2. Drill the hole inside the circle you have drawn.

Choose a spot near the center or closer to the

outside edge of the circle, depending on which

will be easier when you begin to use your saw.

Cutting the speaker hole

Be sure to cut carefully to make the hole as regular as

possible. However, when the speaker is in place, the

frame overlaps the cutting edge by

in. (0.6 cm), which

masks minor cutting inaccuracies.

1. Hold the cutting blade in a vertical position and keep

it straight as you cut the hole.

This helps prevent the blade from angling away from

the outlined circle.

(21.9 cm)

00_791_Speaker_IG.book Page 6 Tuesday, January 26, 2010 1:21 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bose 791 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bose 791

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info