Bedienungsanleitung Bose Cinemate GS series II (Seite 22 von 24) (Englisch)

571108

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

CARE AND MAINTENANCE

EnglishFrançais Español

CARE AND MAINTENANCE

Cleaning your speaker system

• You may clean the surface of your speakers, Acoustimass

module, and Interface module

with a soft, damp cloth. You can use an ammonia-free window cleaner on a soft cloth to

maintain the finish.

• Do not use any sprays near the speakers. Do not use any solvents, chemicals, or cleaning

solutions containing alcohol, ammonia, or abrasives.

• Do not allow liquids to spill into any openings.

• The speaker grilles require no special care, although you may vacuum them carefully,

if necessary.

Limited warranty

The CineMate

™

speaker system is covered by a limited transferable warranty. Details of the

warranty are provided on the product registration card that came with your system. Please fill

out the information section on the card and mail it to Bose.

Accessories

The CineMate speakers are compatible with Bose

mounting accessories, including the

UB-20 wall brackets, UFS-20 floor stands, and UTS-20 table stands. Bose also offers cable

adapters, for use in running speaker cable through walls, and longer speaker wire, as needed.

For further information or to order mounting brackets, stands, or cable adapters, contact your

Bose dealer. Or, to call Bose directly, refer to the address sheet included in the carton.

Troubleshooting

Problem What to do

No power, no

LEDs

• Make sure the Acoustimass

module power switch (230V units only) is turned on.

• Make sure the power cord is inserted securely into the Acoustimass module and plugged firmly

into an operating AC wall outlet (mains).

• Make sure the Interface module is plugged into the Acoustimass module properly.

• Unplug the Acoustimass module power cord from the AC wall outlet for one minute, then recon-

nect it. This allows the unit to reset itself. Check that the red Standby LED on the front of the

Interface module is now lit.

No sound • Make sure the CineMate speaker system is turned on. The green LED on the front of the Inter-

face module should be lit.

• Increase the volume.

• Check to see if the sound source is muted. Press the remote control Mute button to unmute it.

• Make sure the Interface module and speaker cables are both firmly connected to the jacks on

the Acoustimass module.

• Check the speaker connections.

• Unplug the power cord from the outlet for one minute, then reconnect it. This allows the system

to reset itself.

• Check that the correct TV/Video input has been selected. See “Selecting the TV input” on

page 16.

• Check the connections from the Interface module to the TV or other source.

• Check that the TV’s audio output is enabled. See your TV owner’s guide for information.

• If the TV’s audio output is VARIABLE (VAR), make sure the TV’s internal speakers are turned off

and the TV volume is turned up.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bose Cinemate GS series II Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bose Cinemate GS series II

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info