Bedienungsanleitung Bose FreeSpace 4400 (Seite 39 von 70) (Englisch)

497406

Zoom out

Zoom in

Vorherige Seite

1/70

Nächste Seite

36 of 66

6.0 FreeSpace

4400 System Setup

2. Set the minimum output gain.

This sets the desired minimum volume within a zone. Play a

source that will be used in the zone and adjust the volume

slider to the desired minimum level. Raise the minimum gain

stop up to the volume slider level.

3. Set the initial output gain.

When the FreeSpace 4400 system is switched from standby

to operating mode, it loads its configuration (initial settings).

Wherever the volume slider is set when you save the config

uration becomes the initial gain setting.

Page Gain Setup

The Page Gain function allows you to independently define a

page level for each of the four output zones of the FreeSpace

4400 system.

1. Select the Out Gain function for the zone with paging.

2. Using the output gain slider, set the gain to the paging level

you want for the output zone.

3. Click the Set button. The new Page Gain level is displayed

above the Set button.

Programmer’s Note: When working with the Page Gain

function, please note the following behaviors:

• Moving the maximum gain stop to a point below the

current Page Gain setting will set the Page Gain to the

level of the new maximum output gain.

• Moving the minimum gain stop to a point above the cur-

rent Page Gain setting will set the Page Gain to the level

of the new minimum output gain.

• If Auto Volume was calibrated for a zone with paging,

you will be able to adjust the Output Gain and set the

Page Gain when Auto Volume is off.

Output gain controls

Page Gain – Displays the Page Gain setting for the output zone.

Page Gain Set Button – Sets the Page Gain to the level defined

by the gain slider position.

Gain slider – This slide control adjusts the output gain. As you

click and drag the slider, you will hear the level change. Release

the mouse when you hear the level you want. The output gain is

adjusted in an installed system by the Volume up/down buttons

on the AVM (Mute) or AVM (Auto Volume) user interface.

Programmer’s Note: In zones using Auto Volume, the

volume may only be adjusted using the Auto Volume

interface.

Maximum and minimum gain stops – The maximum and min-

imum gain stops determine the maximum and minimum volume

levels. Click and drag each stop to the values you want. If the

stop meets the volume slider, the volume slider will move with the

stop until the new setting is reached.

When a AVM user interface is used in a zone, the volume control

cannot set the gain outside these limits.

Programmer’s Note: In an Auto Volume zone, the

maximum and minimum level stops are disabled once an

Auto Volume calibration is run.

Mute selection – When checked, the Mute selection quiets the

output audio.

Signal level meter – The signal level meter displays the output

level of the FreeSpace 4400 system.

Clipping indicator – The clipping indicator tells you when clip-

ping is occurring in the amplifier. When indicated, clipping is

caused by a low/reduced AC line voltage.

6.3.2 Zone setup

The Zone Setup control panel allows you to select the EQ for the

loudspeakers used in a zone and to document (optional) the

number of loudspeakers in a subzone and their tap settings.

Speaker EQ – The Speaker EQ drop-down list contains a list of

loudspeakers by model name. The selected loudspeaker equal

ization settings are sent to the FreeSpace 4400 system.

Each item in the list indicates a type of mounting: (F) for flush, (S)

for surface, and (P) for pendant. Some items are listed more than

once because they may be mounted in more than one way. For

example, the Model 16 has two entries: one with an (F) for flush,

and one with a (P) for pendant.

The list also includes commonly used groupings, such as combi-

nations of FreeSpace

3 bass and mid/high devices. Use these

settings when you are using the FreeSpace 3 bass on the same

loudspeaker line with other loudspeakers.

Loudspeaker

model drop list

Add

subzone

Delete

subzone

Subzone table

Mount code

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bose FreeSpace 4400 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info