Bedienungsanleitung Bose T8S TONEMATCH (Seite 44 von 48) (Englisch)

704842

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

44 - English

Care and Maintenance

Problem What to do

Poor quality sound from a

microphone or instrument

connected to the T4S/T8S.

• Make sure there is no unwanted zEQ or Para EQ equalization applied.

• Verify that you have selected an appropriate ToneMatch® mixer preset

for your microphone/instrument. If you do not want to use a ToneMatch

mixer preset, make sure ToneMatch is set to Flat.

• Make sure there are no unwanted eects (Comp/Gate, Mod, Delay,

Reverb) on your input channel. Check the Status in the Prefs menu for

any currently active eects.

• Check that the T4S/T8S input Trim is adjusted properly for your

microphone/instrument. The signal LED should be green; if the LED is

red, lower the Trim level until it is green.

• Try a dierent microphone or instrument cable.

• Check the cable connecting your microphone or instrument to the T4S/

T8S mixer. Make sure the cable plug is fully inserted into the microphone/

instrument output connector and the T4S/T8S input connector.

• Check the settings (if any) on your microphone or instrument.

• Check the batteries (if any) in your instrument or microphone.

Not hearing any eects. • Check that you pressed the correct CH Edit button.

• Make sure the FX Mute button is not pressed for the channel in question.

T4S/T8S not responding to

control knobs.

• Turn o the mixer. Wait 30 seconds and turn mixer on again.

Master volume control has no

eect.

• Verify that the Master output is conﬁgured for Post Master Volume

operation in the Prefs menu under Master Out.

With nothing plugged into the

T4S/T8S input connectors, a

slight hum or buzz is heard

from the L1® system.

• Plug the T4S/T8S and the L1 power stand into the same AC (mains) outlet.

• Using an AC outlet tester, test the AC outlet that the T4S/T8S and/or the

L1 power stand is plugged into for reversed or open (hot, neutral, and/or

ground) contacts.

• If using an extension cord, make sure that the cord is also tested as

above.

Too much (or not enough)

bass, mid-range, or high

frequencies.

• Make sure there is no unwanted zEQ or Para EQ equalization applied.

• Verify that you have selected an appropriate ToneMatch mixer preset

for your microphone/instrument. If you do not want to use a ToneMatch

mixer preset, make sure ToneMatch is set to Flat in the Utility category.

Poor-sounding playback of a

stereo recording using a CD

player, MP3 player, or other

such device.

• Connect the left channel of the device to Aux input 5 and the right

channel to Aux input 6 (or 9/10 for T8S). Aux inputs 5/6 (or 9/10) are

designed for line-level inputs.

• Disable any extended bass or EQ features when using CD or mobile

device.

• If you are using recording software on a computer, check the software

requirements. You may need to conﬁgure the software settings for

48kHz/24-bit operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bose T8S TONEMATCH Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bose T8S TONEMATCH

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info