Bedienungsanleitung Bostitch IC50-1-E (Seite 7 von 56) (Alle Sprachen)

721847

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

ADJUSTING THE MAGAZINE

(IC60-1-E & IC70-1-E ONLY)

1. Release the canister latch on the rear of the canister.

(Fig. 8)

2. Pull out the canister bottom by swinging right to left

until tabs disengage. (Fig. 9)

3. Inside the canister bracket there are settings in

inches and millimeters. The canister is adjusted

correctly when the length of fastener being used

isshown in the window of the canister bottom.

4. Push back the canister bottom and engage the latch

ADJUSTING THE MAGAZINE

(IC50-2-E, IC50-1-E, IC90-1-E, IC90P-1-E,

IC90C-1-E ONLY)

1. The magazine contains an adjustable nail platform

on which the nail coil rests. The nail platform can

beadjusted up and down to three nail settings.

2. To change settings, pull up on the post and twist

tothe correct step. (Fig. 10)

Model

Step Number / Nail Length (mm)

1 2 3 4

IC50-2-E 25-27 32 38-45 50

IC50-1-E 25-27 32 38-45 50

IC90-1-E 80-90 70-75 50-65

IC90P-1-E 80-90 70-75 50-65

IC90C-1-E 80-90 70-75 50-65

GUIDE ROD (IC50-2-E & IC50-1-E ONLY)

The tool includes a guide rod that needs to be adjusted

depending on the type of nails:

- The rod should be in the depressed position for

standard plastic inserted nails with 7mm pitch (Fig. 11)

- The rod should be in the released position for wire

welded nails and plastic inserted nails with 6mm pitch

(Fig. 12)

TRIP OPERATION MODE

THESE TOOLS ARE FITTED WITH 2 DIFFFERENT

ACTUATION MODES DEPENDING ON THE MODEL.

m WARNING! Always disconnect air supply before

making adjustments as accidental actuation may

occur, possibly causing injury.

SEQUENTIAL ACTUATION MODE:

Models: IC50-2-E

CONTACT ACTUATION MODE:

Models: IC50-1-E, IC60-1-E, IC70-1-E, IC90-1-E,

IC90P-1-E, IC90C-1-E

IMPORTANT: The IC90C-1-E is fitted with an

auxiliary handle that includes an additional safety lever

(Fig. 13). This additional lever must be fully depressed

throughout the contact actuation sequence for the tool

to drive any fasteners. If the auxiliary handle lever is

not depressed, the tool will not cycle.

SEQUENTIAL ACTUATION

The sequential actuation requires the operator to

hold the tool against the work with the safety yoke

depressed before pulling the trigger. In order to drive

additional fasteners, the trigger must be released and

the tool lifted away from the work, before repeating the

above mentioned steps.

This makes accurate fastener placement easier,

for instance on framing, toe nailing and crating

applications. The sequential actuation allows exact

fastener location without the possibility of driving

a second fastener on recoil, as described under

Contact Trip (below). The sequential actuation tool

has a positive safety advantage because it will not

accidentally drive a fastener if the tool is contacted

against the work - or anything else - while the operator

is holding the trigger pulled.

GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE

compliance for the products.

FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signiﬁent en

rien que les produits soient conformes aux normes CE.

DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen

nicht die CE-Richtlinien für Produkte.

NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet

zeggen dat de producten voldoen aan de CE-vereisten.

DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for

produkterne.

FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-

yhdenmukaisuutta.

GR Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα

αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.

IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la

conformità CE per i relativi prodotti.

NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for

CE-merking for produktet.

PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em

conformidade com a CE para os produtos.

ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la

conformidad con las normas CE de los productos.

SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la

conformidad con las normas CE de los productos.

PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu

nie stanowią deklaracji zgodności CE prezentowanych produktów.

CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu

nie stanowią deklaracji zgodności CE prezentowanych produktów.

SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané

výrobky.

HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem

jelenti a termék CE-megfelelőségét.

RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă

conformitatea CE pentru produse.

Bostitch IC50-1-E Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info