Bedienungsanleitung Bostitch IC90C-1-E (Seite 8 von 56) (Alle Sprachen)

721852

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

CONTACT ACTUATION

THESE TOOLS ARE FITTED WITH CONTACT

ACTUATION.

m WARNING! Always disconnect air supply before

making adjustments as accidental actuation may

occur, possibly causing injury.

m WARNING! Tools marked with this

symbol have either contact actuation,

continuous contact actuation or selectable

actuation with contact actuation selected.

WHEN IN CONTACT ACTUATION MODE:

These tools are designed for use in

production applications such as pallets,

furniture, manufactured housing or

upholstery. DO NOT use for applications such as

closing boxes or crates and ﬁtting transportation safety

systems on trailers and lorries. This tool shall only be

used in safe working places. Care must be taken to

prevent accidental actuation when changing from one

working position to another.

The common operating procedure on “Contact

actuation” tools is for the operator to actuate the

safety trip while keeping the trigger pulled, thus driving

a fastener each time the work is contacted. This will

allow rapid fastener placement on many jobs, such as

sheathing, decking and pallet assembly. All pneumatic

tools are subject to recoil when driving fasteners.

The tool may bounce, releasing the safety yoke and if

unintentionally allowed to re-contact the work surface

with the trigger still actuated (ﬁnger still holding the

trigger pulled) an unwanted second fastener will be

driven.

FASTENER DEPTH CONTROL ADJUSTMENT

IC50-2-E, IC50-1-E ONLY (Fig. 14)

The DIAL-A-DEPTH™ Fastener Control adjustment

feature provides close control of the fastener drive

depth; from ﬂush with the work surface to shallow or

deep countersink.

First, set the air pressure for consistent drive in the

speciﬁc work, then use the DIAL-A-DEPTH™ Fastener

Control adjustment to give the desired depth of drive.

IC90-1-E, IC90P-1-E, IC90C-1-E ONLY (Fig. 15)

The Fastener Depth Control Adjustment feature

provides control of the nail drive depth from ﬂush with

or just above the work surface to shallow or deep

countersink.

m WARNING! Disconnect tool from air supply before

attempting any parts disassembly and before changing

the work contacting element adjustment.

Step 1. Loosen hex screw

Step 2. Push in Locking Button

Step 3. Adjust contact arm up to increase depth of

drive or down to decrease it.

Step 4. Release locking button.

Step 5. Tighten hex screw to lock in place.

DIRECTIONAL EXHAUST DEFLECTOR (FIG 16)

IC50-2-E, IC50-1-E, IC60-1-E, IC70-1-E: Disconnect the

air supply. Rotate exhaust deﬂector to desired position.

Reconnect air supply.

IC90-1-E, IC90P-1-E, IC90C-1-E ONLY: Disconnect the

air supply. Loosen the screw. Adjust to desired exhaust

direction and tighten screw. Reconnect air supply.

DRIVER MAINTENANCE INSTRUCTIONS

Worn driver causing poor quality or loss of power

• Wear on the driving tip will aect the nail drive, giving

symptoms of bent and incompletely driven nails, and

damaged nail heads

• The driver length may be adjusted to allow the driving

tip to be redressed to compensate for wear. Heat and

precise measurement are required. Contact a

qualiﬁed service technician for this adjustment.

• The length setting for a new driver is shown in the

Technical Data Table, column T. Measurement is from

the top face of the piston.

• Note that the measurement U (see Technical Data

Table) from the top of the piston gives the maximum

amount the driver may be adjusted to allow

redressing. Always extend the driver the minimum

amount required to allow redressing to restore the

driving end; several re-dressings will be possible

before this maximum depth is reached.

Note: Driver wear of approximately 3mm can be

tolerated in most applications. However, in dicult

driving applications, driver wear of approximately

1.5 mm. may cause a slight reduction in the apparent

driving power.

GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE

compliance for the products.

FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signiﬁent en

rien que les produits soient conformes aux normes CE.

DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen

nicht die CE-Richtlinien für Produkte.

NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet

zeggen dat de producten voldoen aan de CE-vereisten.

DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for

produkterne.

FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-

yhdenmukaisuutta.

GR Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα

αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.

IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la

conformità CE per i relativi prodotti.

NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for

CE-merking for produktet.

PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em

conformidade com a CE para os produtos.

ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la

conformidad con las normas CE de los productos.

SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la

conformidad con las normas CE de los productos.

PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu

nie stanowią deklaracji zgodności CE prezentowanych produktów.

CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu

nie stanowią deklaracji zgodności CE prezentowanych produktów.

SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané

výrobky.

HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem

jelenti a termék CE-megfelelőségét.

RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă

conformitatea CE pentru produse.

Bostitch IC90C-1-E Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info