Bedienungsanleitung Bostitch MFN201 (Seite 7 von 68) (Alle Sprachen)

721914

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

2. Put the rubber cap slightly inclined on top of the steel stud, push downward with a twisting motion to engage

the rubber cavity over the edge of the steel stud.

3. Once fully engaged over the edge, you can release the mallet from the vise and hit it on solid surface to

properly seat the rubber face on the mallet head.

FOOTKITS (MIIIFS & MIIIFN)

Both the MIIIFS and MIIIFN tools come supplied with an additional Flooring Foot that can be fitted to offer extra

stability when the tool is in use.

Fitting Instructions:

1. Remove the flat head cap screws (Fig. 9a) and plastic spacer (Fig. 9b) located on the underside of the tool.

Note (MIIIFN Only): also remove the 2 front pads (Fig. 9c).

2. Install the pre-finished flooring foot and the proper number of shims (Fig. 10A) as follows:

NOTE: FLOORING PRODUCTS WILL VARY AND THE USER MUST INSURE THE THE TOOL IS SHIMMED PROPERLY

ACCORDING TO THE FLOORING PRODUCT BEING INSTALLED. ONCE PROPERLY SHIMMED, ONLY THE FOOT

WILL CONTACT THE FLOORING.

3. Re-install the flat head screws.

4. Roller adjustment (Fig 11): the tool is shipped with rollers set-up for 5/8”- 3/4” (Fig. 11a) range flooring. For

1/2”- 9/16” range flooring remove o-rings, shafts, rollers and re-install rollers in upper holes (Fig. 11b).

Note: If desired or if proper range of adjustment cannot be achieved, foot may be used without rollers.

FLOORING FOOT INSTRUCTIONS

1. Be sure the foot is flush to the flooring (Fig. 12a). Use the window to verify this (Fig. 12b).

Important: DO NOT STRIKE PRE-FINISHED FLOORING (Fig. 12c)

2. Strike both sides of the foot to set the flooring (Fig. 13a).

3. Actuate the tool after flooring is set (Fig. 13b) and then roll the tool to the next fastener position

CORRECT FASTENER PLACEMENT

When the tool is properly shimmed and with the correct air pressure, the fasteners should be set into the flooring

tongue. (Figs. 14A,B,C). However, some adjustment may be required to ensure the correct drive depth as follows:

Important: Always test on a scrap piece of flooring first.

Shims Recommended:

Flooring Thickness

1/2” (12.7mm)* 3/4” (19mm)

MIIIFN 21

MIIIFS 10

* 1/2” Flooring: remove the bumper spacer (p/n

118076). This is item 22 on your tool parts

illustration.

Fig. 14a

• Air pressure too low.

• Fastener above tongue.

• Increase air pressure.

Fig. 14b

• Air pressure too high.

• Fastener buried.

• Lower air pressure.

Fig. 14c

• Correct air pressure.

• Fastener just below surface.

FT71556-b-0210_Flooring_Tools_Manual:FT71556 15/4/11 09:42 Page 7

GB ©Stanley Bostitch. Not to be reproduced without permission. Unauthorised copies of this

document do not constitute CE compliance for the products.

F ©Stanley Bostitch. Reproduction interdite sans permission préalable. Les copies non autorisées

de ce document ne signifient en rien que les produits soient conformes aux normes CE.

D ©Stanley Bostitch. Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte

Kopien dieses Dokuments erfüllen nicht die CE-Richtlinien für Produkte.

NL ©Stanley Bostitch. Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige

kopieën van dit document willen niet zeggen dat de producten voldoen aan de CE-vereisten.

udgør ikke CE overholdelse for produkterne.

kopiot eivät muodosta tuotteille CE-yhdenmukaisuutta.

εξουσιοδοτημένα αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για

τα προϊόντα.

documento non garantiscono la conformità CE per i relativi prodotti.

dokumentet oppfyller ikke kravene for CE-merking for produktet.

deste documento não estão em conformidade com a CE para os produtos.

documento no suponen la conformidad con las normas CE de los productos.

Nieautoryzowane kopie niniejszego dokumentu nie stanowią deklaracji zgodności CE

prezentowanych produktów.

Nieautoryzowane kopie niniejszego dokumentu nie stanowią deklaracji zgodności CE

prezentowanych produktów.

dokumentu nie sú v súlade s CE pre dané výrobky.

sokszorosított dokumentum nem jelenti a termék CE-megfelelőségét.

Bostitch MFN201 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info