Bedienungsanleitung Bostitch MIIIFN (Seite 6 von 68) (Alle Sprachen)

721916

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Note (MFN201): Because it is a manual tool, sufficient force is required when using the MFN201 to completely

drive flush a single fastener with one strike of the hammer. Do not use the hammer twice on the same fastener,

unless the ratcheting mode is engaged.

Note (MFN201, MIIIFS, MIIIFN): Never hit the plunger with the metal face of the hammer.

CAUTION (MIIIFS & MIIIFN): Installing Pre-finished Flooring

These tools were designed for use in installing unfinished hardwood flooring. They can be used to install pre-

finished flooring, however caution must be used to ensure that the finish is not damaged by the tool. It is

recommended that the tools be tested on a sample section to be certain that the tool and technique of use do

not leave marks on the finish. This procedure should be followed before each job due to variations in flooring

and tool condition.

LOADING THE TOOL

MFN201 (Fig. 4)

1. Release the pusher spring clip and remove pusher blade. (fig 4a)

2. Load fasteners into guide channel.

3. Insert rounded end of pusher blade into channel to retain fasteners.

4. Latch pusher spring clip to notched end of pusher blade. Ensure sufficient engagement ofpusher blade for

smooth fastener feeding. (fig 4b)

MIIIFS (Fig. 5)

1. Pull cover open and insert stick of staples.

2. Push cover forward until the pin snaps into place, locking the cover.

MIIIFN (Fig. 6)

1. Insert nails.

2. Pull pusher assembly back (fig 6a) to engage pusher to strip of nails.

Note: Use only fasteners recommended by Bostitch for use in Bostitch tools or fasteners that meet Bostitch

specifications.

TOOL MAINTENANCE

CAUTION: Pusher spring (constant force spring). Caution must be used when working with the

spring assembly. The spring is wrapped around, but not attached to, a roller. If the spring is extended beyond its

length, the end will come off the roller and the spring will roll up with a snap, with a chance of pinching your

hand. Also, the edges of the spring are very thin and could cut. Care must also be taken to insure no permanent

kinks are put in the spring as this will reduce the spring’s force.

MALLET MAINTENANCE

Over time the rubber face on the mallet may became worn, cracked, or chipped. These are signs that a new

rubber face will need to be installed.

To remove old rubber face:

1. Secure the rubber face in a bench vise. (Fig 7)

2. Pull upward on the handle till the rubber face is released from the steel stud.

To install a new rubber face on the mallet, we recommend doing it in the shop with the use of an arbor press. If

you must do it manually follow these instructions.

1. Secure the mallet head in a bench vise. (Fig 8)

FT71556-b-0210_Flooring_Tools_Manual:FT71556 15/4/11 09:42 Page 6

GB ©Stanley Bostitch. Not to be reproduced without permission. Unauthorised copies of this

document do not constitute CE compliance for the products.

F ©Stanley Bostitch. Reproduction interdite sans permission préalable. Les copies non autorisées

de ce document ne signifient en rien que les produits soient conformes aux normes CE.

D ©Stanley Bostitch. Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte

Kopien dieses Dokuments erfüllen nicht die CE-Richtlinien für Produkte.

NL ©Stanley Bostitch. Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige

kopieën van dit document willen niet zeggen dat de producten voldoen aan de CE-vereisten.

DK ©Stanley Bostitch. Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument

udgør ikke CE overholdelse for produkterne.

kopiot eivät muodosta tuotteille CE-yhdenmukaisuutta.

εξουσιοδοτημένα αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για

τα προϊόντα.

documento non garantiscono la conformità CE per i relativi prodotti.

dokumentet oppfyller ikke kravene for CE-merking for produktet.

deste documento não estão em conformidade com a CE para os produtos.

documento no suponen la conformidad con las normas CE de los productos.

Nieautoryzowane kopie niniejszego dokumentu nie stanowią deklaracji zgodności CE

prezentowanych produktów.

Nieautoryzowane kopie niniejszego dokumentu nie stanowią deklaracji zgodności CE

prezentowanych produktów.

dokumentu nie sú v súlade s CE pre dané výrobky.

sokszorosított dokumentum nem jelenti a termék CE-megfelelőségét.

Bostitch MIIIFN Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info