Bedienungsanleitung Bostitch P51-10B-E (Seite 7 von 39) (Alle Sprachen)

721943

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

3. Snap magazine spring o magazine block.

4. Lift rear of magazine up and pull magazine back.

5. Remove jammed staple.

6. Slide magazine forward, aligning locating pins with

holes in guide.

7. Push rear of magazine; do so with pin in magazine, block

engages hole in frame.

8. Wedge magazine spring back onto magazine block.

JAW CLOSURE (P88SJ-E, P100SJ-E)

The magazine opening of the jaw plate and the tightness

of the staple clinch depends on the number of washers

added to the jaw piston (Fig 4).

This adjustment should be made only by authorised

agents of Bostitch or by other experts giving due regard

to the safety, operating and maintenance instructions

in this manual and the Safety Operating Instructions

Manual.

TROUBLE SHOOTING (P51-5B-E / P51-10B-E)

Problem: Shuttle punches through board:

Solution: Pressure too high; staple leg too short.

Problem: Staple leg buckles and ﬂattens

against work surface:

Solution: Staple leg too long, shuttle not down against

work due to worn shuttle piston o-ring.

Problem: Driver punches through board:

Solution: Worn driver piston bumper.

Problem: Staple ejects from nose before shuttle

contacts work surface:

Solution: Worn shuttle piston o-ring;

excessive air pressure.

Problem: Staple ejects from rear opening in shuttle

Solution: Worn driver piston o-ring

Problem: Air leaking through exhaust port:

Solution: Worn upper driver piston o-ring; worn upper

shuttle piston o-ring; worn valve stem seat.

Problem: Air leakage through nose piece:

Solution: Worn lower driver piston o-ring;

worn shuttle piston o-ring.

Problem: Staples tumbling in staple channel:

Solution: Feed springs overstressed; feed springs

broken; pusher binding on magazine core;

dirt inside magazine; excessive air pressure.

TROUBLE SHOOTING (P88SJ-E, P100SJ-E)

Problem: Serious air leaking from valve holes:

Solution: Lower O-ring and trigger valve worn out or

not in position. Replace.

O-ring plug of piston rod. Replace.

O-ring valves worn out. Replace.

Plug loose. Tighten.

Problem: Air leaking from hole under cylinder bridge:

Solution: O-ring piston worn out. Replace.

Problem: Does not drive staple but jaw closes:

Solution: Small valve dirty. Lubricate.

Exhaust pinhole plunger or too tight.

Clean pinhole and outer diaphragm.

Rod hole outside of tolerance limits.

Return within tolerance limits (0.75 mm).

Insucient lubrication. Lubricate.

Problem: Air leaking from valve holes:

Solution: O-ring piston valve not completely closed.

Replace inner piston valve O-ring and

lubricate.

Problem: Staples are not completely closed

Solution: Jaw fall block is bent or damaged.

Replace block.

Problem: Jaw does not return:

Solution: Bridge is not squared up. Square up.

Problem: Slow operations:

Solution: Lack of lubrication. Lubricate.

Rod hole outside tolerance levels.

Return within tolerance limits (0.75 mm)

Problem: Staples jam:

Solution: Driver worn out. Replace.

De-jamming block springs slack. Replace.

GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE

compliance for the products.

FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signiﬁent en

rien que les produits soient conformes aux normes CE.

DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen nicht

die CE-Richtlinien für Produkte.

NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet

zeggen dat de producten voldoen aan de CE-vereisten.

DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for

produkterne.

FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-

yhdenmukaisuutta.

GR Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα

αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.

IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la

conformità CE per i relativi prodotti.

NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for

CE-merking for produktet.

PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em

conformidade com a CE para os produtos.

ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la

conformidad con las normas CE de los productos.

SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la

conformidad con las normas CE de los productos.

PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu

nie stanowią deklaracji zgodności CE prezentowanych produktów.

CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu

nie stanowią deklaracji zgodności CE prezentowanych produktów.

SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané

výrobky.

HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem

jelenti a termék CE-megfelelőségét.

RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă

conformitatea CE pentru produse.

Bostitch P51-10B-E Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info