Bedienungsanleitung Bostitch RC-10 (Seite 10 von 118) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

721839

Zoom out

Zoom in

Vorherige Seite

1/118

Nächste Seite

To avoid overheating of the electric motor, this compressor is designed for intermittent operation as indicated on the

technical dataplate (for example, S3-25 means 2.5 minutes ON, 7.5 minutes OFF).

SAVE THESE INSTRUCTIONS AND MAKE THEM AVAILABLE TO OTHER USERS OF THIS TOOL!

OPERATION AND MAINTENANCE

NOTE: The information contained in this Instruction Manual is designed to assist you in the safe operation and

maintenance of the compressor. Some illustrations in this Instruction Manual may show details or attachments that

differ from those on your own compressor.

INSTALLATION

Remove the compressor from its packing, makes sure it is in perfect condition, checking if it was damaged during

transport, and carry out the following operations:

Fit the wheels and rubber tab on the tanks on which they are not already fitted, observing the instructions in (fig.1a &

1b). Also fit the Air Filter (Fig 2). Position the compressor on a flat surface or with a maximum permissible inclination of

10°, in a well aired place, protected against atmospheric agents and not in a place subject to explosion hazard. If the

surface is inclined and smooth, check if the compressor moves while in operation - if it does, secure the wheels with

two wedges. If the surface is a bracket or a shelf top, make sure it cannot fall, securing it in a suitable way. To ensure

good ventilation and efficient cooling, the compressor must be at least 100 cm from any wall. Compressors fitted on

the tank, with fixed feet, should not be rigidly secured to the ground. In this case, we advise you to fit 4 anti-vibration

supports. Verify that the tanks have been drained and are clear of any moisture or dirt.

INSTRUCTIONS FOR USE

-Take care to transport the compressor correctly, do not overturn it or lift it with hooks or ropes. Check oil level,

consulting the reference marks on the stick (fig. 3).

Oil lubricated compressors may come with a bottle of oil to fill or top up the compressors - note that not all oil supplied

may be needed to fill the unit to the correct level.

NOTE: Some units (MRC6, RC-10) are equipped with an oil-free pump. There is no oil to replace or check.

ELECTRICAL CONNECTION

Single-phase compressors are supplied with an electrical cable and a two-pole & earth plug. The compressor must be

connected to a grounded power socket (fig.4).

IMPORTANT: Never use the ground socket instead of the neutral wire. The ground connection must be made to meet

safety standards (EN 60204). The plug of the power cable must not be used as a switch, but must be fitted in a power

socket controlled by a suitable differential switch (thermalbreaker).

STARTING

Check that the mains power matches that indicated on the electrical data-plate (fig.5) - the permissible tolerance range

is +/-5%. Turn or press into position “0” (according to the type of pressure switch fitted on the appliance) the knob

located on the upper section (fig. 6A, 6B, 6C). Fit the plug in the power socket and start the compressor, turning the

pressure switch knob into position “I”.

The compressor is fully automatic, and is controlled by the pressure switch which stops it when tank pressure

reaches maximum value and restarts it when it falls to minimum value. The pressure difference between maximum and

minimum values is usually about 2 bar (29 psi). E.g.: the compressor stops when it reaches 8 bar (116 psi - maximum

operating pressure) and restarts automatically when the pressure inside the tank drops to 6 bar (87 psi). After

connecting the compressor to the power line, load it to maximum pressure and check exactly how the machine is

operating.

NOTE: The head/cylinder/delivery tube unit can reach high temperatures. Take care when working near these parts,

and do not touch them to avoid possible burns.

IMPORTANT

The electro-compressors must be connected to a power socket protected by a suitable differential switch

(thermal-breaker). The motor is equipped with an automatic thermal breaker located inside the winding - this stops

the compressor when motor temperature reaches excessively high values (180

C). If the breaker is tripped, the

compressors restart automatically after 10 to 15 minutes.

GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE

compliance for the products.

FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signifient en

rien que les produits soient conformes aux normes CE.

DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen nicht

die CE-Richtlinien für Produkte.

NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet

zeggen dat de producten voldoen aan de CE-vereisten.

DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for

produkterne.

FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-

yhdenmukaisuutta.

GR Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα αντίγραφα του παρόντος

εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.

IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la

conformità CE per i relativi prodotti.

NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for CE-

merking for produktet.

PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em

conformidade com a CE para os produtos.

ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la

conformidad con las normas CE de los productos.

SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la

conformidad con las normas CE de los productos.

PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie

stanowią deklaracji zgodności CE prezentowanych produktów.

CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie

stanowią deklaracji zgodności CE prezentowanych produktów.

SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané

výrobky.

HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem jelenti

a termék CE-megfelelőségét.

RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă

conformitatea CE pentru produse.

Bostitch RC-10 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info