Bedienungsanleitung Bostitch RN46DW-2-M (Seite 7 von 56) (Alle Sprachen)

721874

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

TRIP OPERATION MODE

THESE TOOLS ARE FITTED WITH 2 DIFFFERENT

ACTUATION MODES DEPENDING ON THE MODEL.

m WARNING! Always disconnect air supply before

making adjustments as accidental actuation may occur,

possibly causing injury.

SEQUENTIAL ACTUATION MODE:

Models: RN46-2-E, RN46K-2-E, RN46DW-2-M

CONTACT ACTUATION MODE:

Models: RN46DW-1EPAL

SEQUENTIAL ACTUATION

The sequential actuation requires the operator to hold

the tool against the work with the safety yoke depressed

before pulling the trigger. In order to drive additional

fasteners, the trigger must be released and the tool

lifted away from the work, before repeating the above

mentioned steps.

This makes accurate fastener placement easier, for

instance on framing, toe nailing and crating applications.

The sequential actuation allows exact fastener location

without the possibility of driving a second fastener on

recoil, as described under Contact Trip (below). The

sequential actuation tool has a positive safety advantage

because it will not accidentally drive a fastener if the tool

is contacted against the work - or anything else - while

the operator is holding the trigger pulled.

CONTACT ACTUATION

THESE TOOLS ARE FITTED WITH CONTACT ACTUATION.

m WARNING! Always disconnect air supply before

making adjustments as accidental actuation may occur,

possibly causing injury.

m WARNING! Tools marked with this symbol

have either contact actuation, continuous

contact actuation or selectable actuation with

contact actuation selected.

WHEN IN CONTACT ACTUATION MODE:

These tools are designed for use in production

applications such as pallets, furniture,

manufactured housing or upholstery. DO NOT

use for applications such as closing boxes or crates

and ﬁtting transportation safety systems on trailers

and lorries. This tool shall only be used in safe working

places. Care must be taken to prevent accidental

actuation when changing from one working position to

another.

The common operating procedure on “Contact

actuation” tools is for the operator to actuate the safety

trip while keeping the trigger pulled, thus driving a

fastener each time the work is contacted. This will allow

rapid fastener placement on many jobs, such as pallet

assembly. All pneumatic tools are subject to recoil when

driving fasteners.

The tool may bounce, releasing the safety yoke and if

unintentionally allowed to re-contact the work surface

with the trigger still actuated (ﬁnger still holding the

trigger pulled) an unwanted second fastener will be

driven.

LOCK-OUT MECHANISM

This tool is equipped with a Lock-Out mechanism, which

is activated when the magazine be-comes empty. This

indicates to the operator that reloading is necessary. The

tool may not actuate when the Lock-Out is engaged, as

shown. (Fig 5)

SHINGLE GAUGE

This gauge can be used to control shingle spacing. To

adjust, push the gauge lever and slide the gauge to the

desired shingle exposure as shown. (Fig 6)

Warning! Disconnect the air supply before making

adjustments.

CLEANING THE NAILER

Warning! Do not use petrol or similar highly ﬂammable

liquids to clean the nailer.

Vapour could be ignited by a spark, causing an explosion.

Tar and dirt may build up on the nose and trip lever. This

can prevent correct operation. Remove any build-up

with diesel or paraﬁn. Do not dunk the nailer into these

solvents beyond the height of the nail heads, to avoid

getting the solvent into the drive cylinder. Dry o the

nailer before use. Any oil ﬁlm left after cleaning will

accelerate the tar build-up, and the nailer will require

more frequent re-cleaning.

Note: Solvents sprayed on the nose to clean and free up

the trip may have the opposite eect! The solvent may

soften the tar on the shingles and cause tar build-up to be

accelerated. Dry operation is better, as noted above.

“DIAL-A-DEPTH™” FASTENER CONTROL

ADJUSTMENT (FIG 7)

The DIAL-A-DEPTH™ Fastener Control adjustment

feature provides close control of the fastener drive depth;

from ﬂush with the work surface to shallow or deep

countersink. First, set the air pressure for

consistent drive in the speciﬁc work, then use the

DIAL-A-DEPTH™ Fastener Control adjustment to

give the disired depth of drive.

GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE

compliance for the products.

FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signiﬁent en

rien que les produits soient conformes aux normes CE.

DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen nicht

die CE-Richtlinien für Produkte.

NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet

zeggen dat de producten voldoen aan de CE-vereisten.

DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for

produkterne.

FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-

yhdenmukaisuutta.

GR Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα

αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.

IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la

conformità CE per i relativi prodotti.

NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for

CE-merking for produktet.

PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em

conformidade com a CE para os produtos.

ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la

conformidad con las normas CE de los productos.

SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la

conformidad con las normas CE de los productos.

PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu

nie stanowią deklaracji zgodności CE prezentowanych produktów.

CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu

nie stanowią deklaracji zgodności CE prezentowanych produktów.

SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané

výrobky.

HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem

jelenti a termék CE-megfelelőségét.

RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă

conformitatea CE pentru produse.

Bostitch RN46DW-2-M Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info