Bedienungsanleitung Bostitch SB-1850BN (Seite 5 von 36) (Alle Sprachen)

721911

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

SAFETY INSTRUCTIONS

 IMPORTANT READ CAREFULLY: It is important that all operators read and understand all

sections of this Tool Technical Data manual and the separate Safety and Operating Instruction

Manual which come with this tool. Failure to do so could result in you or others in the working area to be

seriously injured.

 WARNING! Eye protection in accordance with 89/686/EEC, and with equal or greater grade than

defined in EN166 should be used. However all aspects of operators work, environment and other type/s of

machinery being used, should also be considered when selecting any personal protection equipment.

Note: Non-side shielded spectacles and face shields alone do not provide adequate protection.

 WARNING! To prevent accidental injuries:

•

Never place a hand or any other part of the body in fastener discharge area of tool.

•

Never point tool at yourself or anyone whether it contains fasteners or not.

•

Never engage in horseplay.

•

Never pull the trigger unless the nose is directed towards the work.

•

Always handle the tool with care.

•

Do not pull the trigger or depress the trip mechanism whilst loading the tool.

•

To prevent accidental actuation and possible injury, always disconnect air supply.

1. Before making adjustments. 2. When servicing the tool. 3. When clearing a jam. 4. When tool is not in

use. 5. When moving to a different work area, as accidental actuation may occur, possibly causing injury.

•

Read the additional Safety & Operating instructions booklet before using tool.

•

Do not use oxygen and combustible gases as an energy source for pneumatically operated tools.

•

The operation of this tool can cause sparks and act as a source of ignition for flammable fuels and

gases.

1. Depress magazine release button and pull back magazine. (Fig 1a & 1b)

2. With magazine fully open, insert fasteners. Points must be against bottom of

magazine. (Fig 2a & 2b)

3. Push magazine forward. (Fig 3)

4. Continue pushing until latch is engaged. (Fig 4)

1. Depress magazine release button and pull back magazine. (Fig 5)

2. Open magazine fully. Turn tool sideways with discharge area pointed away from

yourself & others. Load staples in channel. (Fig 6)

3. Push magazine forward. (Fig 7)

4. Continue pushing until latch is engaged. (Fig 8)

1. Open the magazine: Pull pusher back to engage latch. (Fig 9)

2. With magazine fully open, insert fasteners. Points must be against bottom of

magazine. (Fig 10)

3. Close magazine: Release latch by pulling latch tab and pusher together

slightly to disengage, slide pusher against the nails. (Fig 11)

“DIAL-A-DEPTH™” FASTENER CONTROL ADJUSTMENT (FIG 12A-12B)

The DIAL-A-DEPTH™ Fastener Control adjustment feature provides close control of the fastener drive depth;

from flush with the work surface to shallow or deep countersink. First, set the air pressure for consistent drive

in the specific work, then use the DIAL-A-DEPTH™ Fastener Control adjustment to give the desired depth of

drive.

SB-1842BN,

SB-1850BN,

SB-2IN1,

SB-HC50FN

(Figs 1-4)

SB-150SX,

SB-150SXHD

(Figs 5-8)

SB-1664FN

(Figs 9-11)

FT60032-b-909_HCFN_Manual:WS60032 HCFN Manual 27/10/09 13:49 Page 5

GB ©Stanley Bostitch. Not to be reproduced without permission. Unauthorised copies of this

document do not constitute CE compliance for the products.

F ©Stanley Bostitch. Reproduction interdite sans permission préalable. Les copies non autorisées

de ce document ne signifient en rien que les produits soient conformes aux normes CE.

Kopien dieses Dokuments erfüllen nicht die CE-Richtlinien für Produkte.

kopieën van dit document willen niet zeggen dat de producten voldoen aan de CE-vereisten.

udgør ikke CE overholdelse for produkterne.

kopiot eivät muodosta tuotteille CE-yhdenmukaisuutta.

εξουσιοδοτημένα αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για

τα προϊόντα.

documento non garantiscono la conformità CE per i relativi prodotti.

dokumentet oppfyller ikke kravene for CE-merking for produktet.

deste documento não estão em conformidade com a CE para os produtos.

documento no suponen la conformidad con las normas CE de los productos.

Nieautoryzowane kopie niniejszego dokumentu nie stanowią deklaracji zgodności CE

prezentowanych produktów.

Nieautoryzowane kopie niniejszego dokumentu nie stanowią deklaracji zgodności CE

prezentowanych produktów.

dokumentu nie sú v súlade s CE pre dané výrobky.

HU ©Stanley Bostitch. A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül

sokszorosított dokumentum nem jelenti a termék CE-megfelelőségét.

Bostitch SB-1850BN Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info