Bedienungsanleitung Bostitch SC50HPB-E (Seite 6 von 39) (Alle Sprachen)

721946

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

LOADING THE TOOL

1. Slide the fasteners onto the magazine rail (Fig 2A)

towards the front of the magazine (Fig 2B)

2. Pull back the pusher past the fasteners (Fig 3)

3. Gently release the pusher, so that it remains behind the

fasteners, pushng them along the magazine (Fig 4)

Note: Use only fasteners recommended by

Bostitch for use in Bostitch tools or fasteners which

meet Bostitch speciﬁcations.

TOOL OPERATION

1. The operator of the tool should understand that the

success of operating this tool depends on the method

(or technique) that the handles are operated. The

single most important issue will be in the outward

movement of the handles during the ring loading

cycle. The handles must be opened completely to

the full open position. This will need to be done in a

continuous motion to prevent the tool from jamming.

Failure to do this will cause the ring to feed short of

the latch nose.

The ring must feed beyond the latch nose to allow the

latch to position behind the ring and prevent the ring

from deforming during closure.

2. Any outward movement of the handles must result in

the full ring loading cycle. Partial outward movement

will push a ring only part way forward. When the

handles are returned to the start position and then

opened again the ring being fed on the second cycle

will jam into the previously incompletely cycled ring.

This ring jamming will cause the tool to jam and

lock the handles. If the handles become locked the

operator will need to remove the jammed rings from

between the jaws. This can be accomplished in the

following ways:

• Most of the time this can be accomplished by using

a screwdriver or other probing device to free the

jammed ring(s).

• If using the probe doesn’t remove the rings, than the

following will be necessary. Remove all rings from

the magazine.

Place the ring pusher in the parked position. This is

a point at the rear of the spring spool bracket. Just

hook the pusher in the slot near the bottom rear of the

bracket. Loosen both pivot bolt nuts 4 – 6 turns, this

will allow more clearance between the jammed rings

and the magazine. This should now allow the removal

of the jammed ring(s).

• In the event the above still doesn’t allow the removal

of the jammed ring(s) then it will be necessary to

remove the magazine completely. When re-installing

the pivot bolts or tightening the pivot bolt nuts, care

must be taken not to overtighten the nuts.

m This tool is intended to be used for ﬁxing wire to wire

in automotive, mattress assembly and cage/wire assembly

or for closures in packaging etc. DO NOT USE for fastening

unsuitable materials which could cause buckling of the

fasteners and damage to the tool. If you are unsure of the

suitability of this tool for certain applicartions, please

contact your local sales oce.

WARNING! MOVEABLE PARTS & JAW (FIG 1)

•

These tools feature moveable parts including the jaw to

close the fasteners. Make sure only the material to be

fastened is placed within the jaws of this tool to avoid

the danger of crushing of ﬁngers. Keeps hands clear at

all times to prevent serious injury.

m Warning!

•

IMPORTANT SAFETY INFORMATION ENCLOSED.

•

READ THIS MANUAL BEFORE OPERATING THE TOOL.

•

SAVE FOR FUTURE REFERENCE.

•

FAILURE TO OBSERVE THE FOLLOWING

WARNINGS COULD RESULT IN INJURY.

•

Keep body stance balanced and ﬁrm.

Do not overreach when operating this tool.

•

Use protective equipment such as

glasses, gloves, safety shoes as well

as acoustic protection. Remain vigilant,

use common sense and pay attention

when using the machine.

•

Always wear suitable CE marked

eye protection when operating or

performing maintenance on this tool.

GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE

compliance for the products.

FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signiﬁent en

rien que les produits soient conformes aux normes CE.

DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen nicht

die CE-Richtlinien für Produkte.

NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet

zeggen dat de producten voldoen aan de CE-vereisten.

DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for

produkterne.

FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-

yhdenmukaisuutta.

GR Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα

αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.

IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la

conformità CE per i relativi prodotti.

NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for

CE-merking for produktet.

PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em

conformidade com a CE para os produtos.

ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la

conformidad con las normas CE de los productos.

SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la

conformidad con las normas CE de los productos.

PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu

nie stanowią deklaracji zgodności CE prezentowanych produktów.

CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu

nie stanowią deklaracji zgodności CE prezentowanych produktów.

SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané

výrobky.

HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem

jelenti a termék CE-megfelelőségét.

RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă

conformitatea CE pentru produse.

Bostitch SC50HPB-E Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info