Bedienungsanleitung Boston M series (Seite 5 von 72) (Deutsch, Englisch, Französisch, Italienisch, Spanisch, Schwedisch)

582007

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Position subwoofer

in corner for maximum

bass output

Unpacking the System

Carefully unpack the speakers. If there is any sign of damage from transit, report it immediately to your dealer or delivery service.

Retain the shipping carton and packing materials for future use.

Grilles

The cloth grilles should remain on the speaker during normal use. However, to remove a grille, use your ﬁngers to carefully

pry the top edge of the grille away from the cabinet so you can insert your ﬁngers between the grille and the cabinet. Then

slide your ﬁngers down the inside of the grille frame from top to bottom which will cause the grille to pop free. The grille is

NOT designed to be removed by only pulling on one side. The pins that hold the grille can be damaged. Also, do not use any

objects other than your ﬁngers to remove the grille as the ﬁnish or grille may be damaged. Be careful to keep rings, watches

and other sharp objects from scratching the ﬁnish or tearing the grille cloth.

To replace the grille, carefully align the two pins at the top of the grille with their corresponding grommets and gently push

them in until the grille is supported by the grommets. Then work your way down the grille gently pushing the grille pins into

the grommets evenly until the grille is fully seated. Be careful to align the pins with the grommets so the cabinet, grille pins

and grommets are not damaged. Also, take care to support the speaker so it does not tip over or fall oﬀ its mounting location

while the grille is being removed or replaced. MCenter Note: The same grille removal and replacement procedures apply

to the MCenter except you will begin at the left or right side and work towards the opposite side. MSubwoofer Note: The

MSubwoofer grille is not removable.

Feet & Spikes

The M350, M340 and M250 come with rubber feet installed at the factory which are ideal for hardwood ﬂoors. Spikes are also

included for placement on a carpeted surface. To install the spikes, carefully lay the speaker on its back on a soft, debris-free

surface and remove the rubber feet by hand turning them counter-clockwise. Thread the spikes by hand to make sure they

are inserted properly. Save the rubber feet for future use.

The M25, MCenter, and MSurround come with rubber stand-oﬀs that are designed to be attached to the bottom of the

loudspeaker

when stand, shelf or cabinet mounting. This will minimize the vibration transferred from the loudspeaker to the

stand, shelf or cabinet. It will also help to protect the ﬁnish of the loudspeaker and the mounting location. The MSubwoofer

comes with rubber feet installed at the factory.

MSurround Note: It is recommended to mount the rubber stand-oﬀs on the back of the side panels of the MSurround if it is

going to be wall mounted. This will minimize the amount of vibration that is transferred directly to the wall. You may need to

adjust the depth of the mounting screws to help ensure that the speaker is not mounted too loosely or too tightly.

Where to Place the Speakers

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Boston M series Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info