Bedienungsanleitung Bowers Wilkins Panorama (Seite 12 von 157) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

562447

Zoom out

Zoom in

Vorherige Seite

1/157

Nächste Seite

mode, surround mode selected, stereo mode selected

and wide stereo mode selected.

3.3 Switching On and Using Panorama

Ensure that the DVD player is connected to Panorama

Input 1, switched on and correctly set up with a disc

playing. In its default setup Panorama will switch on

automatically when an input signal is present on Input

1. It will also automatically select Input 1 together with a

default group of setup parameters that have been

specifically chosen to provide good initial performance

in a typical domestic environment. If a signal is present

on Input 1 Panorama will immediately reproduce it.

Note: If no sound is reproduced either the input cable is

plugged-in to the wrong input socket or there is no

output signal from the DVD. Select Input 2 using the

remote handset to check the former. To check the latter,

disconnect the input cable from Panorama and examine

its end. A faint red light shining from the end of an

optical cable confirms that a signal is present.

Once reproducing audio satisfactorily, use the Panorama

handset or front panel controls to raise or lower the

volume, select inputs or select audio decode modes. The

following paragraph describes audio decode modes.

3.4 Audio Decode Modes

Audio from DVD, videotape and, on occasions,

broadcast sources can be encoded with a variety of

surround sound formats. Panorama is capable of

decoding Dolby Digital, DTS, Dolby PLII surround sound

formats as well as providing conventional and “wide’

stereo reproduction. Not all decode modes however

can be used with each Panorama input or with each

programme material format. Figure 11 illustrates the

decode modes available with each programme material

format and Panorama input.

Panorama will detect Dolby Digital and DTS encoded

programme material and automatically select the

appropriate decode mode. With other programme

material, digital or analogue, the most likely appropriate

decode modes are highlighted in the table. The

Panorama display will show SURR when surround

modes are engaged, STEREO when conventional stereo

is engaged and WIDE when wide stereo is engaged.

digital or analogue material is reproduced, voice mode

implements a custom B&W designed filter algorithm.

The Panorama control panel, illustrated in Figure 10,

incorporates a display, a standby/input button, a

decode mode button and volume adjustment buttons.

The display illustrates the currently selected Panorama

input until a function button is pressed. It will then

display the selected function for a short time. The

display also incorporates six indicators which illuminate

to indicate the currently selected programme decode

Setup Mode. See the Panorama Setup

sections for more information.

mode Selects Panorama home theatre programme

decode modes.

– Lowers Panorama volume.

Selects Panorama inputs.

Note: When reproducing Dolby Digital encoded

material, voice mode implements the compression and

filter algorithm inherent in the encoding. When other

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bowers Wilkins Panorama Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info