Bedienungsanleitung Bowers-Wilkins T7 (Seite 5 von 98) (Alle Sprachen)

580540

Zoom out

Zoom in

Vorherige Seite

1/98

Nächste Seite

ENGLISH

Diagram 5

Bluetooth setup

5. T7 audio inputs

T7 can play audio either wirelessly from a compatible

Bluetooth device or through a wired connection from

a device with an analogue output.

T7 will select between its Bluetooth and wired inputs

automatically although the Bluetooth input has

priority. The following input selection rules apply:

• If T7 is connected via Bluetooth and a plug is

inserted in the Auxiliary input socket, T7 will

switch to the Auxiliary input.

• If T7 is playing audio through its Auxiliary input

and a Bluetooth stream is received or the

Bluetooth button is pressed, T7 will switch to the

Bluetooth input.

• If T7 is playing audio through its Auxiliary input

and the cable is disconnected T7 will switch to

the Bluetooth input and attempt to connect to

the primary paired source device.

Note: If T7 is connected via Bluetooth while an

Auxiliary input cable is also connected, a new

analogue audio signal will not automatically

switch T7 to its Auxiliary input.

5.1 Bluetooth connection

To connect T7 to a Bluetooth enabled audio device it

must rst be “paired” with the device. Once paired, a

Bluetooth device and T7 will “remember” each other

and be able to connect when within range.

T7 will remember up to eight paired Bluetooth

devices. The rst paired device will be designated

as the “primary” device, additional devices will be

designated as “secondary” devices.

The primary device will be connected when within

range, and the T7 Bluetooth button is pressed.

Secondary devices will not connect automatically

when in range but must be connected via their

Bluetooth settings.

It is possible for two paired devices to be connected

to T7. However, audio will only be heard from one

device at any one time. When two devices are

connected the other device can override the active

stream.

To pair a Bluetooth device with T7 follow the steps

described below.

• With T7 switched on, press and hold the

Bluetooth button for 2 seconds. The indicator

will ash and T7 will provide audible feedback

when it enters “pairing” mode.

Note: T7 will automatically exit from Bluetooth

pairing mode if no device is paired within 5

minutes.

• Open the Bluetooth settings on the source device

and ensure Bluetooth is switched on. Once

discovered, Bowers & Wilkins T7 will appear as

an available Bluetooth device. Select T7 and close

the Bluetooth settings. T7 Bluetooth indicator will

ash as pairing is underway and illuminate fully

when pairing is established. T7 will also provide

audible feedback when pairing is established.

Note: If your Bluetooth audio source device does

not support “simple” pairing and requests a four

digit code, enter ‘0000’.

• Once a connection has been established, ensure

that T7 is selected as the speaker output. Audio

will now be heard through T7.

2 seconds

Devices

Bowers & Wilkins T7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bowers-Wilkins T7 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info