Bedienungsanleitung Bowflex SelectTech BD552i (Seite 7 von 24) (Englisch)

737206

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Operation

Given the importance of this locking mechanism, it is critical that you understand how it operates, and periodically test it to make sure it is

functioning correctly.

Testing proper locking mechanism function

1. With the dumbbell handle set in the dumbbell base, turn both adjustment knobs to the number 2. You

will know you have fully and correctly selected the number when you feel the adjustment knob settle

into a notch (known as a detent). You will also hear a slight, but audible, clicking noise that corresponds

with the detent locations for each number.

2. You should be able to withdraw the handle from the base leaving all the weight plates behind.

3. With the handle removed from the base, grab one adjustment knob with your other hand and gently

attempt to turn the knob, the knob should not rotate. A locking pin in the mechanism will have

engaged the rotational assembly when the unit was withdrawn from the base. Perform this test with all

adjustment knobs.

Do not use too much force to try to turn the locked adjustment knob. Too much force can damage the locking mechanism.

4. After confirming the proper function of the locking mechanism as described above, return and fully insert the dumbbell handle back into

the base assembly.

5. With the handle back in the base, turn the adjustment knob on one side to a position that is between the numbers 2 and 3. This

represents an incomplete weight selection where the adjustment knob has not fully selected a weight and the knob is in-between the

selection detents (clicks).

6. With the selection knob in this improper position, gently attempt to lift up on the handle to remove it from the base. You should find that

the handle is locked to the base and cannot be removed with light pressure, as it can normally.

7. Return the improperly selected adjustment knob to a full and proper weight selection and assure that the dumbbell handle can once

again be removed.

8. Repeat this test for all adjustment knobs.

9. Assure the entire dumbbell handle assembly is properly tightened. Do this by setting the adjustment knobs to 2 and removing the

handle assembly from the base. Grab both adjustment knobs and very slightly push and pull the knobs toward and away from the

handle grip. The knobs should not exhibit free play and all of the selection discs should feel tightly connected.

10. You have now tested the function of the locking mechanism. We suggest you repeat this test monthly to make sure that the locking

mechanism operates correctly.

Do not engage the locking mechanism and use the handle to try to lift the dumbbell and base together. To lift the

dumbbell and base together, engage the locking mechanism and use the lift handles molded into the base assembly.

If the dumbbell locking mechanism operates unsatisfactorily in the test procedure above, do the following:

1. Stop use of the product immediately until approved service is available.

2. Contact your Bowflex

retailer for service.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bowflex SelectTech BD552i Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bowflex SelectTech BD552i

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info