Bedienungsanleitung Bowflex TC10 (Seite 43 von 52) (Englisch)

737224

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Assembly / Owner’s Manual

Condition/Problem Things to Check Solution

Unit will not power up/turn on/start Outlet Make sure outlet is functioning correctly. Verify this by plugging another

device (ex: lamp) into the outlet. If outlet is connected to a light switch,

check to make sure it is on. If outlet is not functioning nd a working

outlet.

Power cord not plugged in Make sure the power cord is rmly secured to A/C inlet on the unit and

rmly inserted into a non-GFI wall socket.

Power switch turned off Make sure the power switch at the rear of the unit is in the “ON” posi-

tion. Switch will light up red to indicate power is present.

Safety key not plugged in Plug Safety Key into Console (See Safety Key (Emergency Stop Procedures)

within Features section).

Speed displayed is not accurate Display set to wrong unit of mea-

sure. (English/Metric)

Change display units.

Walking belt misalignment Rear belt guides Belts should ride on top of triangular black belt guides at rear of

treadles.

Tracking adjustment Belts are not required to be perfectly centered and are typically farther

out in the rear than they are in the front. This may vary depending on

user’s stride. If belt is tracking to one side far enough to cause rubbing

of belt, consult the “Adjusting the Walking Belts” procedure.

Speed dependent grinding or

scraping noise

Belt alignment Check walking belt alignment. Belt contact with metal guides under

Treadle can make a loud grinding sound. If belts are misaligned, adjust

walking belt.

Rollers or motor Contact your local Bowex

distributor for further assistance.

Hesitation or belt slipping when

walking on unit

Walking belt tension Adjust walking belt tension by following the “Adjusting the Walking Belt”

procedure.

Knocking noises when unit is

operating

Igus bushing If knocking sound seems to be coming directly from the rear roller,

check Igus (yellow “hat” shaped) bushings and replace if cracked.

Hydraulic cylinder bolts Check and tighten both upper and lower bolts that connect the hydraulic

cylinders to the unit.

Belts stop turning while in use Safety key Plug Safety Key into Console (See Safety Key (Emergency Stop Procedures)

in Features section).

Motor overload Unit may be overloaded and drawing too much current, causing unit

to shut power down to protect motor. Consult belt lubrication schedule

to determine if belts need lubrication, check walking belt tension, and

restart unit.

Outlet Outlet may not have enough power available for the machine due to

other devices on same circuit. Remove any devices from power circuit

and restart machine.

Console displays “C”, “S”, or “H”

with a number

Unit needs to be restarted Cycle power off for 10 seconds using power switch at rear of unit, then

restart.

Error code diagnostic Contact your local Bowex

distributor for further assistance.

Console displays “LUbE” code Belt lubrication Consult lubrication schedule and apply if necessary. Push START but-

ton.

Troubleshooting

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bowflex TC10 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info