Bedienungsanleitung Braun 5050cc - 5748 (Seite 13 von 73) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

664926

Zoom out

Zoom in

Vorherige Seite

1/73

Nächste Seite

Installing the Clean&Charge Station (see fig. D)

• Remove the protection foil from the Clean&Charge

Station display.

• Using the special cord set (10), connect the

station power socket (12) to an electrical outlet.

• Press the lift button (13) at the rear side of the

Clean&Charge Station to lift up the housing.

• Hold the cleaning cartridge (17) down on a flat,

stable surface (e.g. table).

• Carefully remove the lid from the cartridge.

• Slide the cartridge from the rear side into the base

of the station until it snaps into place.

• Slowly close the housing by pushing it down until

it locks.

Charging the shaver in the Clean&Charge Station

(see fig. D)

Insert the shaver head down into the cleaning station.

Important: The shaver needs to be dry and free

from any foam or soap residue!

The contacts (7) on the back of the shaver need to

align with the contacts (14) in the station. Push the

shaver in the correct position.

A beep sound confirms that the shaver sits properly

in the station. Charging will start automatically.

Model 5090cc: The Clean&Charge Station analyzes

the hygiene status. The status is shown by the

cleaning program indicators

in the Clean&Charge

Station display (15) more details see chapter

«Cleaning programs» below.

Cleaning the shaver (see fig. D)

When the cleaning indicator lights up in the shaver

display, insert the shaver into the Clean&Charge

Station, upside down and with the front showing (with

released head lock/contact alignment/beep sound).

Cleaning programs

5090cc: The hygiene status will be analyzed and one

of the following program indicators will light up.

short economical cleaning

normal level of cleaning

high intensive cleaning

5070cc/5050cc: One standard cleaning program

included.

Start automatic cleaning

Start the cleaning process by pressing the start

button (16). If status light (15a) does not shine

(Clean&Charge Station switches to stand-by after

ca. 10 minutes), press start button twice. Otherwise

cleaning will not start. For best shaving results,

we recommend cleaning after each shave.

Each cleaning program consists of several cycles,

where cleaning fluid is flushed through the shaver

head. Depending on your Clean&Charge Station

model and/or program selected, the cleaning time

takes up to 3 minutes. During this time the status light

blinks. Leave the shaver in the station for drying.

It takes several hours until remaining moisture

evaporates depending on the climatic conditions.

Afterwards the shaver is ready for use.

After completing the cleaning and charging proce-

dure, all indicators turn off.

Removing the shaver from the Clean&Charge

Station (see fig. E)

Hold the Clean&Charge Station with one hand and

tilt the shaver slightly to the front to release it.

Cleaning Cartridge / Replacement (see fig. F)

When the level indicator

lights up permanently

red, the remaining fluid in the cartridge is sufficient

for about 3 more cycles. When the level indicator

blinks red, the cartridge needs to be replaced -

about every 4 weeks (when used daily).

After having pressed the lift button (13) to open the

housing, wait for a few seconds before removing

the used cartridge to avoid any dripping. Before

discarding the used cartridge, make sure to close

the openings using the lid of the new cartridge,

since the used cartridge will contain contaminated

cleaning solution.

The hygienic cleaning cartridge contains ethanol or

isopropanol (specification see cartridge), which once

opened will naturally evaporate slowly. Each cartridge,

if not used daily, should be replaced after approxi-

mately 8 weeks to ensure optimal disinfection.

The cleaning cartridge also contains lubricants for

the shaving system, which may leave residual marks

on the outer foil frame and the cleaning chamber

of the Clean&Charge Station. These marks can be

removed easily by wiping gently with a damp cloth.

Accessories

Braun recommends changing your shaver’s

Foil & Cutter cassette every 18 months to maintain

your shaver’s maximum performance.

Available at your dealer or Braun Service Centres:

• Foil & Cutter cassette: 52S/52B

• Cleaning cartridge Clean&Charge Station: CCR

• Braun Shaver cleaner spray

Environmental notice

Product contains batteries and/or recyclable

electric waste. For environment protection do

not dispose of in household waste, but for

recycling take to electric waste collection

points provided in your country.

The cleaning cartridge can be disposed of with

regular household waste.

Subject to change without notice.

For electric specifications, see printing on the

special cord set.

97144167_5090cc_MN_S6-76.indd 1397144167_5090cc_MN_S6-76.indd 13 11.09.14 08:1211.09.14 08:12

CSS APPROVED Effective Date 26Sep2014 GMT - Printed 30Oct2014 Page 13 of 76

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Braun 5050cc - 5748 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info