Bedienungsanleitung Braun BD 5007 (Seite 15 von 91) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

790306

Zoom out

Zoom in

Vorherige Seite

1/91

Nächste Seite

DO NOT activate the device if the treatment window (1) is not placed in full contact

with the skin.

DO NOT block the cooling vents. The device may overheat and pose an electric

shock risk or fire hazard.

HOW TO USE

Preparing the treatment area

Remove any visible hair on the skin before using the device. You may use your preferred hair removal

method. Ensure there is no hair remaining above the surface of the skin as this can damage the removable

front (9) and may cause treatment discomfort. Clean the treatment area and pat it dry.

To power on the device:

Plug the mains cord (8) into an electrical outlet. Plug the power supply (7) into the power socket (6).

The LED power bars (3) will light up once and, a fan starts running. This means the device is in READY

mode. During operation, the device will heat up slightly.

Light intensity button (4)

Normal setting: After plugging in, the device operates with full light intensity shown by a white

indicator light.

Gentle setting: Press button (4) in order to operate with reduced light intensity. The indicator light

shines blue.

Extra gentle setting: Press the button a second time: The light flashes blue.

To return to full power, press the button again.

Gentle and extra gentle settings are meant for sensitive areas and first time users. With reduced light

intensity, more treatments may be required to see the desired effects.

Automatic skin tone reading

When both skin tone sensors (2) have skin contact, the device reads your skin tone and selects the

appropriate light intensity which is indicated by white LEDs on the Power bars (3). These confirm that the

device is ready to flash.

light skin tone U high light intensity

dark skin tone U low light intensity

no LEDs no skin contact U device cannot be activated

red LED invalid skin tone U device cannot be activated

Patch Test

Before your first treatment, we recommend you test your skin for reaction to Braun Silk·expert on a small

area of skin of the body part you plan to treat (about 2 x 3 cm in size; equivalent to the size of two flashes,

side by side).

Perform a patch test as described BELOW in chapter «TREATMENT MODES», section «Precision mode».

Wait 48 hours to examine the test area. If the skin appears normal, begin your first treatment. If a skin

reaction develops, discontinue using the device and consult your physician. Do not treat the patch tested

area for at least one week after the test.

91573656_BD5001-BD5006_BD5009_Euro_A_S4-94.indd 1591573656_BD5001-BD5006_BD5009_Euro_A_S4-94.indd 15 19.06.17 15:2919.06.17 15:29

CSS APPROVED Effective Date 21Jun2017 GMT - Printed 30Aug2017 Page 15 of 94

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Braun BD 5007 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info