Bedienungsanleitung Braun Clean Charge Flex Integral (Seite 7 von 40) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

454360

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

English

Braun Clean&Charge has been developed

for cleaning, charging and storing your

shaver. Clean your shaver daily in the

Clean&Charge.

During the automated cleaning process,

the shaver is switched on and off at intervals

to obtain best cleaning results. Since the

specially formulated cleaning fluid contains a

small amount of oil, the cleaning procedure

also fulfills the lubrication needs of the

shaver.

Important

•

Only use the power supply cord set supplied

with the shaver.

•

In order to avoid any leakage of the cleaning

fluid, place the appliance on a flat, stable

surface or use the wall holder (not included

in all versions). Do not tip, move suddenly

or transport in any way if a cleaning cartridge

is installed.

•

Do not place the appliance in a mirror cabi-

net, nor store it over radiators, nor place it

on polished or laquered surfaces. Do not

expose to direct sunlight.

•

The appliance contains highly

flammable liquid. Keep it away from

sources of ignition. No smoking.

Keep out of reach of children. Do not refill

cartridge. Use only original Braun refill

cartridge.

•

When cleaning the shaver, its protection

cap should be removed.

A Description

1 Lift button for cartridge exchange

2 Contact bow

3 Release button

4 Operation mode selector

5 «clean» light:

cleaning process indicator

6 «charge» light:

charging process indicator

7 «cartridge» light:

cartridge replacement indicator

8 Cleaning cartridge

Wall holder

(not included in all versions)

Mount the wall holder with plugs and screws

to a smooth wall so that the standing surface

for the Clean&Charge is horizontal.

Technical specifications

•

Power consumption:

3 W when cleaning

7 W when charging

•

Power supply: 100-240 V

/50 or 60 Hz

(automatic adaptation)

•

Input voltage: 12 V

B Before using Clean&Charge

First charge:

For the first charge of the shaver, connect

the power supply cord set directl

y to the

shaver, charge it for 4 hours and shave at

least once.

Only then can the shaver be cleaned or

recharged in the Clean&Charge.

If the rechargeable battery is discharged,

select the combined «clean» + «charge»

programme rather than the «clean»

programme alone.

Installing the cartridge

•

Press the lift button (1) to open the housing.

•

Hold the cartridge down on a flat, stable

surface (e.g. table). Carefully remove the lid

from the cartridge. Slide the cartridge into the

base as far as it will go.

•

Slowly close the housing by pushing it down

until it locks.

Replacing the cartridge

After having pressed the lift button to open

the housing, wait for a few seconds before

removing the used cartridge.

Before discarding the used

cartridge, make

sure to close the openings using the lid of the

new cartridge, since the used cartridge will

contain contaminated cleaning solution.

5302450_C&C_S6-44 Seite 8 Montag, 11. Juni 2001 3:41 15

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Braun Clean Charge Flex Integral Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info