Bedienungsanleitung Braun Gillette Venus Naked Skin - 6028 (Seite 9 von 73) (Dänisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

695213

Zoom out

Zoom in

Vorherige Seite

1/73

Nächste Seite

Facial Treatment (women only)

Using Venus Naked Skin

to remove

unwanted facial hair requires care and

special guidance to prevent any possible

adverse reaction. It is recommended

that before treating the face, other body

areas are treated ﬁrst.

Avoid tanning including outdoor sun

bathing, tanning treatments in a salon

before and during treatment, or use of

a tanning lotion or cream before and

during treatment as the device may not

work for you. Further, darker skin may

absorb too much light energy, which may

cause discomfort/pain.

IMPORTANT:

• Do not treat the eyebrows or areas

around the eyes, the scalp, the

nostrils, the ears.

• Do not use on moles or any dark

(pigmented) areas.

Before Treatment

1. Determine if the face may be treated,

by using the skin color chart and the

skin tone sensor. Because the face is

unavoidably exposed to sunlight, it

may be darker than other body areas.

2. Perform a patch test: test your skin

for reaction in a hair-free area below

the ear (see chapter titled “Patch

Test”).

3. After this patch test, wait 48 hours,

examine the treated area and if it

appears normal, begin treating the

upper lip, chin or jaw.

Getting started

1. Remove all cosmetics, lotions and

creams (including self tanning) from

the area you wish to treat.

2. Remove any visible hair.

3. Use the skin tone sensor to conﬁrm

suitability for treatment. Do NOT use if

the skin tone sensor indicates red (IIIII).

Always start with the lowest setting

when using on the face, regardless of

the skin tone sensor reading. This may

require you to manually reduce the

energy level to the lowest setting (IIII)

if you are a lighter skin tone (I-III). Do

this by pressing the white button on

the skin tone sensor until the lowest

setting is lit (IIII).

Treating the face, cheek and jaw

1. Apply a thick layer of Activating

Gel to the area to be treated (see

illustration below).

2. Wipe excess gel from your hands.

3. You may choose to use a mirror to

help position the handset for treating

facial areas.

4. Select a spot on the edge of the

treatment zone. Place handset ﬁrmly

on the skin so that both contact bars

on the outer corners of the treatment

window are placed in the Activation

Gel that is on the skin surface. The

white light of the Activation button

signals you have the proper contact.

If the white light does not appear, be

sure to adjust the handset so that both

bars remain in contact with the skin.

IMPORTANT:

Before pressing the activation button,

close your eyes or look away as the

light is very bright.

5. Press the Activation button.

You may feel a warm sensation.

HOW TO USE

1514

5. Remove the handset from your skin.

The two contact bars and treatment

window will leave marks in the

Activating Gel to help track your

treatment progress.

6. Venus Naked Skin

should be used

on the skin in continuous rows. Your

next selected treatment spot should

be adjacent to the previous. There

should be no gaps between treatment

areas. When placing the handset

onto the gel on your skin, the edge

of the treatment window and the two

contact bars should line up with the

marks from the previous treatment

area.

WARNING:

DO NOT discharge the device on the

same site more than once to avoid

possible adverse skin effect. If your skin

blisters or burns, STOP IMMEDIATELY.

Soothe the area with cooling gel packs.

Seek medical advice immediately.

7. You will need to wait approximately

4 – 6 seconds for the unit to recharge

before it is ready to activate again.

The Skin Tone Sensor button ﬂashes

to show the unit is recharging. When

the light glows WHITE constantly,

it’s ready for use again. Repeat

the process above until you are

ﬁnished treating the treatment area.

Periodically wipe the treatment

window to ensure it is clean and free

of any debris.

SLEEP Mode Timeout

• When the unit is left “inactive”

(i.e., no buttons are pushed or the

Skin Tone Sensor is not removed/

replaced) for 55 minutes, then the

unit will enter a low power SLEEP

mode.

• In SLEEP mode, all the lights are off

except for the RED Skin Tone

Sensor button which will make a

single ﬂash once every 3 seconds.

You must take a skin tone reading

to get out of SLEEP mode.

8. When you have ﬁnished treating

an area, wipe away any excess

Activating Gel from the handset and

the area you have treated. Place the

handset back on the base unit.

9. Check the treated area to see if you

develop any skin reactions. If you

experience a side effect, refer to page

9 in this user guide.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Braun Gillette Venus Naked Skin - 6028 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Braun Gillette Venus Naked Skin - 6028

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info