Bedienungsanleitung Braun Multiquick 7 (Seite 6 von 35) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

454304

Zoom out

Zoom in

Vorherige Seite

1/35

Nächste Seite

Safety fuse

If the motor switch is turned on, but the motor sud-

denly stops or does not run, the built in safety fuse

has been activated. Should this happen, turn the

appliance off and wait until the motor has cooled off

(approximately 15 minutes).

If the motor will not start when switching it on again,

repeat the cooling off procedure (see above).

After use, turn off the appliance and unplug it.

Before using

All parts of the grinder attachment were covered with a

lubricating film before leaving the factory. They must be

washed before using the first time (see «Cleaning»).

Assembly

– Please note the correct assembly order of

parts

1 -5.

– The sharp side of the blade

3 must face the disc 2.

– Guide the notch

B in the disc 2 over the protrusion

E in the grinder head 5.

– After assembling the parts

2 -4, screw the cap 1

moderately tight onto the grinder head

The assembled grinder head

5 is joined to the motor

unit

9 with a bayonet lock. Insert the metal housing into

the motor unit by holding the filling shaft of the grinder

head at an angle of 45° clockwise (the marking on

the grinder head has to match the marking on the

motor unit (A)). Turn the grinder head anti-clockwise in

the direction of the upright arrow (A) until the filling shaft

snaps into place in an upright position. Place the feeder

tray

6 on the filling shaft.

To remove the grinder head

5 press the release button

e and turn the grinder head clockwise 45° as shown in

picture B.

• In order to avoid any risk caused by the rotating

blade make sure that you only attach the grinder

head

5 to the motor part after it has been completely

assembled with disc, blade and worm.

• Before attaching / replacing accessories that are in

movement during operation, switch off the appliance

and unplug it.

Operating

Turn on the motor before filling with meat, fish,

vegetables etc. To do so, press the on switch

H so that

it engages.

To turn off the appliance, press the off switch

In case the appliance is clogged, stop it by pressing the

off switch

Then press the reverse button

∞ (not longer than

10 seconds).

To continue mincing, press the on switch again.

Important: Wait until the appliance has stopped

completely before pressing the reverse button or the on

switch.

Before processing meat, remove tendons and bones

and cut it into strips. Besides meat, the machine will

also process fish, vegetables, onions, soaked bread

rolls, boiled potatoes, stoned plums for jam. Fill the

prepared meat or vegetables into the feeder tray

6 and

push it down into the filling shaft with the pusher

Never use a fork, a spoon handle or a similar object.

If meat is crushed instead of being cut properly, please

check

whether the meat grinder is assembled correctly

(e. g.

whether you have perhaps over-looked inserting

one of the parts) or clean the blade

3 and disc 2.

Notice

• Before mincing frozen meat, defrost it to such a

degree that you can cut it into cubes of appropriate

size. These cubes can be processed with the

appliance.

• When processing food with high power consumption

– e. g. sunflower seeds mixed with oats at a ratio

of 1:3 (approximately 800 W) – do not exceed an

operating time of 10 seconds.

• Before using the «Kubbe» attachment / Sausage

filler

l, the meat has to be ground twice.

Cleaning

Wipe the motor unit

9 with a damp cloth only and wipe

it dry. All other parts can be washed in hot water with

normal dishwashing liquids.

Storage

There is a practical cord storage

j at the base of the

unit (C).

Subject to change without notice.

Please do not dispose of the product in the

household waste at the end of its useful life.

Disposal can take place at a Braun Service

Centre or at appropriate collection points

provided in your country.

99268865_G3000_S4-38 Seite 6 Dienstag, 6. April 2010 3:11 15

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Braun Multiquick 7 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info