Bedienungsanleitung Braun PL5227 (Seite 17 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

790296

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

Do not use abrasive cleaning agents. These may damage the device or scratch the

glass filter.

Do not attempt to use this device other than for removing unwanted hair.

Do not use the device on a surface other than skin. Do not press the treatment

button when the treatment window (1) is not placed in full contact with the skin.

Do not block the cooling vents. The device may overheat and pose an electric

shock risk or fire hazard.

How to use

Preparing the treatment area

Remove any visible hair on the skin before using the device. You may use your preferred hair removal

method. To keep the treatment window clean and intact, ensure there is no hair remaining on the skin

surface. Clean the treatment area and pat it dry.

To power on the device:

Use the mains cord (8) to connect the base station to an electrical outlet. Press any button (4 or 5) to

activate the device. The LED power bars (3) will light up once and a fan starts running. This means the

device is in READY mode. During operation, the device will heat up slightly.

Automatic light adaptation

When both skin tone sensors (2) have skin contact, the device reads your skin tone and selects the

appropriate light intensity which is indicated by white LEDs on the Power bars (3). These confirm that the

device is ready to flash.

light skin tone U high light intensity

dark skin tone U low light intensity with fast flash rate

no LEDs no skin contact U device will not flash

red LED invalid skin tone U device will not flash

Gentle mode

Push the gentle mode button (4) to reduce the light intensity. You can toggle through the following 3

settings:

Standard: 3 indicator lights

Gentle: 2 indicator lights

Extra gentle: 1 indicator light (lowest light intensity with fast flash rate)

Gentle and extra gentle settings are intended for sensitive areas and first time users. With reduced light

intensity, more treatments may be required to see the desired effects.

The power bars flash to confirm a change in the light intensity setting.

When holding the gentle mode button (4) longer than 3 seconds, the device is deactivated.

After 10 minutes without use, the device is automatically deactivated.

Press any button to re-activate it.

Patch Test

Before your first treatment, we recommend you test your skin for reaction to Braun Silk·expert on a small

area of skin of the body part you plan to treat (about 2 x 3 cm in size; equivalent to the size of two flashes,

side by side).

Perform a patch test as described below in chapter «Treatment methods», section «STAMPING».

Wait 48 hours to examine the test area. If the skin appears normal, begin your first treatment. If a skin

reaction develops, discontinue using the device and consult your physician.

91840600_Victoria2_PL5_Euro1.indd 1791840600_Victoria2_PL5_Euro1.indd 17 13.01.21 10:0413.01.21 10:04

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Braun PL5227 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info