Bedienungsanleitung Braun Silk Expert Pro 3 PL3139 (Seite 15 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

790286

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

How to use

Preparing the treatment area

Remove any visible hair on the skin before using the device. You may use your preferred hair removal

method. To keep the treatment window clean and intact, ensure there is no hair remaining on the skin

surface. Clean the treatment area and pat it dry.

To power on the device:

Use the mains cord (8) to connect the base station to an electrical outlet. Press the gentle mode button (4)

to activate the device. The LED power bars (3) will light up once and, a fan starts running. This means the

device is in READY mode. During operation, the device will heat up slightly.

Automatic light adaptation

When both skin tone sensors (2) have skin contact, the device reads your skin tone and selects the

appropriate light intensity which is indicated by white LEDs on the Power bars (3). These confirm that the

device is ready to flash.

light skin tone U high light intensity

dark skin tone U low light intensity

no LEDs no skin contact U device will not flash

red LED invalid skin tone U device will not flash

Gentle mode

Push the gentle mode button (4) to reduce the light intensity. The gentle mode indicator lights up when it is

activated. To deactivate it, press the gentle mode button again.

The power bars flash to confirm a change in the light intensity setting.

When holding the gentle mode button (4) longer than 3 seconds, the device is deactivated.

After 10 minutes without use, the device is automatically deactivated.

To reactivate it, press the gentle mode button.

Patch Test

Before your first treatment, we recommend you test your skin for reaction to Braun Silk·expert on a small

area of skin of the body part you plan to treat (about 2 x 3 cm in size; equivalent to the size of two flashes,

side by side).

Perform a patch test as described below in chapter «Treatment methods», section «STAMPING».

Wait 48 hours to examine the test area. If the skin appears normal, begin your first treatment. If a skin

reaction develops, discontinue using the device and consult your physician. Do not treat the patch tested

area for at least one week after the test.

Treatment methods

The area to be treated must be hair-free, clean and dry. Before pushing the treatment button, look away

from the device to avoid the bright light. In seldom cases, a user may find the flash too bright. However,

there is no safety risk associated with this. For increased comfort, we recommend treating in a well-lit

room to help reduce the perceived brightness.

GLIDING

for fast and efficient

treatment of large areas

(e.g. legs).

STAMPING

for treating small,

hard-to reach areas

(e.g. face for females,

bikini line, underarms,

knee, chin, ankles)

1. Place the treatment window firmly on your skin, ensuring both skin sensors have skin contact.

The power bars (3) show white LEDs

91584520_Victoria_Pro3_Euro_01.indd 1591584520_Victoria_Pro3_Euro_01.indd 15 15.06.20 13:0615.06.20 13:06

P&G RELEASE 06/18/2020 11:19:24 AM Printed 2020-06-18 Page 19 of

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Braun Silk Expert Pro 3 PL3139 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info