Bedienungsanleitung Braun TA 1050 (Seite 8 von 9) (Englisch)

111555

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

PROBLEM

All the indicator

lights are flashing.

The machine will not

move past STANDBY.

The Auto Mode

is not working.

My cup is overflowing.

My cup doesn’t fit.

Trouble shooting

12 Trouble shooting Trouble shooting 13

In the table below are solutions to problems that may occur. If you do not

find an appropriate solution, please refer to the “Tassimo careline” section.

SITUATION

1. Water level is too low.

2. No T-DISC in machine.

3. T-DISC is damaged.

4. Machine not prepared for use.

5. Internal machine fault.

The brew mechanism may not

be closed properly.

Bar code reader may not be able

to read the T-DISC label.

Each drink has been formulated

to produce the perfect amount

of liquid. Be sure that you are

using the right sized cup for

your drink.

The cup stand is too close to

the brew mechanism.

SOLUTION

1. Refill the water container.

2. Place a T-DISC, label side down,

on the T-DISC holder and close

the brew mechanism.

3. Clean the bar code reading

window or replace the T-DISC.

4. Follow the procedure “Preparing

Your Machine for Use”.

5. Contact Tassimo careline.

Make sure that a T-DISC is placed

on the T-DISC holder and the brew

mechanism is firmly closed.

Clean the bar code reading window.

Replace the T-DISC.

You can still enjoy your preferred

drink by using the Manual Mode.

Ensure that you use the following

recommended cup sizes:

Espresso

75ml

Cappuccino

200ml

Coffee, Caffè crema, Chocolate*and Tea

280ml

Try lowering the cup stand to fit your

cup. You can also temporarily remove

the cup stand and drip tray, leaving

the splashback in place.

PROBLEM

Liquid is splashing

out of the cup.

The machine is leaking

from the brew

mechanism.

The machine is leaking

from the bottom.

My drinks are brewing

shorter than usual.

I have lost my

cleaning disc.

My machine is not

operating; there are

no lights illuminated.

SITUATION

Cup is placed too far away

from the brew mechanism.

1. T-DISC is damaged or leaking.

2. The piercing unit is not

fitted properly.

1. Drip tray is full of water.

2. Splashback is not properly

fitted.

The machine may require

descaling.

A cleaning disc is needed to

rinse and descale the machine.

The electrical supply may not be

connected properly.

SOLUTION

Adjust the height of the cup stand

up to ensure that the cup is closer to

the brew mechanism.

Press the start/stop button to

stop the brew cycle. Slowly open the

brew mechanism, remove the

T-DISC, and clean the inside of the

brew mechanism. Remove and

refit the piercing unit.

1. Empty the removable drip tray.

2. Remove and refit the splashback,

cup stand, and drip tray back

on the machine.

Descale the machine following the

“Descaling” procedure.

Contact Tassimo careline.

Check that the machine is properly

plugged into the electrical supply.

Check the on/off switch at the

back of the machine.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Braun TA 1050 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info