Bedienungsanleitung Breezy BasiX 2 Plus (Seite 17 von 80) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

713921

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

RubiX

HEIGHT-ADJUSTABLE ARMRESTS

To adjust the height, pull the lever (1) and

push the armrest to the desired height.

Afterwards make sure that the lever (1)

locks back into position. Removing the

armrest is carried out in the same way.

To remove the sideguard completely, push

the lever (2). When fitting the sideguard, the lever (2) must also be

pulled.

Always make sure that the sideguard locks into position

correctly in the receiver. (Fig. 34)

Fig.34

Options – Hemiplegic armrest

HEMIPLEGIC ARMREST

The hemiplegic armrest can be

adjusted both in length and angle.

You can adjust the length by

pushing the armrest after having

loosened the 2 rotary screws (1).

To adjust the angle, open the

release lever (2) and rotate the

armrest to the desired position,

then tighten it again (Fig. 35).

Fig.35

ANTI-TIP TUBES

Anti-tip tubes provide additional

safety for inexperienced users when

they are still learning how to operate

their wheelchair. They prevent a

wheelchair from tipping over

backwards. The anti tip tube should

be inserted into the frame tube until

the first of the two spring buttons

enters the first hole in the frame tube,

(Fig.36).

WARNING!

Incorrect setup of the anti-tips will increase the risk of a rearwards

tip. You must swing the anti-tips upwards when going up or down

large obstacles, (such as a kerb), to prevent them from touching the

ground, then rotate them back down to the normal position.

NOTE: Do not insert both buttons of the anti tip tube into the frame

tube as this could damage the anti Tipp and cause a loss of

effectiveness. By pushing on the Second exposed release button,

the safety wheels can be set upwards or removed. There must

always be a gap of between 3 cm and 5 cm between the tube and

the ground. You must swing the safety wheels upwards when going

up and down large obstacles (such as a kerb) to prevent them from

touching the ground. Then rotate the safety wheels back down to

the normal position (Fig. 36).

WARNING!

Incorrect set up of the anti tips will increase the risk of a rearwards

tip.

Options – Anti-Tip Tubes

Fig.36

WARNING!

Before using your wheelchair ensure the seat belt is worn and

correctly adjusted before use.

The lap belt is fitted to the wheelchair as shown in the illustrations.

The seat belt comprises 2 halves. They are fitted using the existing

seat stay retaining bolt fitted through the eyelet on the belt. The belt

is routed under the rear of the side panel. (Fig. 37)

Adjust the belt position so buckles are in the centre of the seat. (Fig.

38)

Adjust lap belt to suit the user’s needs as follows:

To increase the belt

length

To reduce the belt

lenght

Feed free belt

through slide adjust-

ers and male buckle

to provide more belt

length.

Feed free belt back

through male buckle

and slide adjusters.

Ensure belt is not

looped at male

buckle.

Options – Lap belt

Fig.37

Fig.38

Type B

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Breezy BasiX 2 Plus Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info