Bedienungsanleitung Breezy RubiX 2 XL Komfort (Seite 13 von 80) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

713920

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

RubiX

Handling

FOLDING UP

First remove the seat cushion and the

back seat shell from the wheelchair and

flip up the (platform) footplate or the

individual footrests. Take hold of the

sling or the seat tubes in the middle,

from the back and pull upwards. The

wheelchair will then fold up. To fold

your wheelchair so that it is as small as

possible, e.g., to put into a car, you can

remove the footrests (depending on the

model). For this purpose, open the latch

from the outside and swing the footrest to the side. Then the footrest

only has to be drawn out of the receiver tube (Fig. 1).

UNFOLDING

Press down on the seat tube (see

figure). Your wheelchair is then unfolded.

Now snap the seat tubing into position in

the seat saddle. This can be facilitated

by slightly tipping your wheelchair, as

this means that the weight is taken off

one of the rear wheels. Be careful not

to get your fingers caught in the

cross-tube assembly. Refit the seat

and the back seat shell (Fig. 2).

GETTING INTO YOUR WHEELCHAIR INDEPENDENTLY

(FIG. 3)

• The wheelchair should be pushed up against

a wall or solid piece of furniture;

• The brakes should be on;

• The footplates should be hinged up;

• The user can then lower himself into the chair;

• The footplates should then be pushed down

and the feet rested on them in front of the

heel loops.

GETTING OUT OF YOUR WHEELCHAIR

INDEPENDENTLY (FIG. 4)

• The brakes should be on;

• The hinged footplates should be hinged up;

• With one hand on each armrest, the person

should bend slightly forward to bring the body

weight to the front of the seat, and with both

feet firmly on the ground, one foot well back,

push up into the upright position.

WARNING!

• When standing, do not stand on the footplates or the

wheelchair will tip up. It is easier and safer to get into your

wheel chair if you turn the footplates up and out of the way or

take them off the wheelchair.

• Always engage the wheel brakes when transfering in or out of

the wheelchair.

Fig. 3

Fig. 4

Options - Brakes

Options – Step Tubes

STEP TUBES

Tipping tubes are used by attendants

to tip a wheelchair over an obstacle

Simply step on the tube to push a

wheelchair, for example, over a kerb

or step (Fig. 5).

CAUTION!

Sunrise Medical strongly recommends the use of a step tube on

transit wheeled models and also on any model where attendant use

is the predominant intended use, as damage to the backposts may

occur if you pull back on them to tip the wheelchair, in order to

overcome obstacles.

WHEEL LOCKS

Your wheelchair is equipped with

two wheel locks. They are applied

directly against the tyres. To engage,

press both brake levers forward

against the stops. To release the

locks, pull the levers back to their

original positions.

Braking power will decrease with:

• Worn tyre tread

• Tyre pressure that is too low

• Wet tyres

• Improperly adjusted wheel locks

The wheel locks have not been

designed to be used as brakes for a

moving wheelchair. The wheel locks

should therefore never be used to

brake a moving wheelchair. Always

use the hand-rims for braking. Make

sure that the gap between the tyres

and wheel locks complies with given

specifications. To readjust, loosen the screw and set the

appropriate gap. Then re-tighten the screw (Fig. 6-7).

CAUTION!

After each adjustment of the rear wheels, check the wheel lock gap

and re-adjust if necessary.

Mounting the wheel lock too close towards the wheel will result in a

higher effort to operate. This might cause the brake lever extension

to break!

Leaning onto the brake lever extension while transferring will cause

the lever to break! Splashing water from tyres might cause the

wheel lock to malfunction.

DRUM BRAKES

Drum brakes permit safe and

convenient braking for an attendant.

They can also be set with the aid of a

locking lever (1) to prevent rolling.

The lever must snap audibly into place.

Drum brakes are not influenced by air

pressure inside the tyres (Fig.8).

WARNING!

Drum brakes must only be adjusted by

authorised dealers

Always operate the two brakes simultaneously to guarantee the

control of the driving direction!

Drum brakes can only be used as a dynamic brake to stop the

wheelchair while driving.

Always engage the wheel locks to secure the wheelchair during a

short or long stop, or for transfer.

Fig. 5

Fig. 1

Fig. 2

FIG. 6

FIG. 7

18 MM

Fig. 8

QUICK-RELEASE AXLES ON REAR WHEEL

The rear wheels are equipped with

quick-release axles. The wheels

can thus be fitted or removed without

using tools. To remove a wheel, simply

depress the quick-release button on

the axle (1) and pull the wheel off the

axle (Fig. 5).

CAUTION!

Hold the quick-release button on the

axle depressed when inserting the

axle into the frame to mount the rear

wheels. Release the button to lock the

wheel in place. The quick-release button should snap back to its

original position

Fig. 5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Breezy RubiX 2 XL Komfort Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info