Bedienungsanleitung Bresser 4701170 (Seite 12 von 36) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

784604

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

6. Eyepiece

Remove one eyepiece from its eyepiece holder (6) and slide it into the

eyepiece connection (3). Tighten the holding screws (No. 5). Start with

the lowest magnification eyepiece, which has the highest focal length

printed on it (e.g. 20 mm or 25 mm, depending on your model) to locate

objects and find the correct focus. If you have the object you want

to view centred in the field of view, switch to a higher magnification

by using an eyepiece with shorter focal length. After changing the

eyepiece, it might be necessary to adjust the focus again (see section

8).

7. Dust cover

Remove the dust cover (15) that protects the objective lens of the opti-

cal tube opening (2).

8. Focus wheel

To get objects into focus, your telescope is equipped with a precise

focus control. When you use the telescope for the first time, you might

need to turn the focus wheel (4) multiple times to achieve a focused

image. To try it out, pick a landmark or a building far away in daylight

or bright twilight, and turn the focus wheel until the object comes into

focus. Remember, objects to be observed cannot be closer than 20

metres away.

Part II – Handbox

1. Batteries

Remove the cover of the battery compartment (11), located on the top

side of the mount's base, and insert the batteries in the battery holder

(No. 2). Use 6 AA batteries and make sure the polarities are aligned

correctly. Place the holder into the compartment and cover it. Do not

use rechargeable batteries.

2. Handbox

Ensure that the on/off switch is in the off position (No. 8). Remove the

handbox from the handbox tray (7), and plug one end of the cable into

the port labelled with "HBX" and the other one into the RJ-45 port of

the handbox. Flip the switch to the on position. The handbox display

should light up, accompanied by a sound.

3. Setup

Time and Date

After turning on the handbox, you will be prompted to enter the date

and time. Do so by navigating with the arrow keys and entering the

numbers with the number pad (7) on the handbox. When done, press

the centre key (5), located between the arrow keys.

Daylight saving time

If the daylight saving time is in effect, select status:on. If daylight saving

time is not in effect, select status:off.

Location

When asked for your location, you can either choose a city near you

by selecting the 'Country & City' option or enter your GPS coordinates

by selecting 'Custom Site'.

a) Country & City

Select the country where you are by using the up and down arrow

keys. Then select the city by using the left and right arrow keys. When

done, use the centre key (5) to select the location.

b) Custom Site

Enter the details of your location as follows:

Name: Enter a custom name for your location.

Lon: Enter the longitudinal coordinate of your location.

Lat: Enter the latitudinal coordinate of your location.

Zone: Enter the time zone of your location.

Example:

Name:

Berlin ; Lon: E013° 25` ;

Lat: N52° 30` ; Zone: E01

Time zone east of Greenwich:

E01-E12

Time zone west of Greenwich:

W01-W12

Greenwich time zone (GMT):

E00 oder W00

OTA (Optical Tube Assembly) Zero

Here you will be asked to provide the orientation of the telescope.

In the 'Azi:' field, enter '000'.

In the 'Alt:' field, enter '00'.

Open the Altitude and Azimuthal locking knobs. Adjust the telescope

so that the tube opening (2) is pointing directly north and is level. It

is recommended that you use the included compass (18) and bubble

level to make sure the device is positioned accurately. You can put the

compass into the eyepiece connection (3). Then retighten the locking

knobs.

4. Alignment

In order to use your telescope's Go To mode, you must align the tel-

escope properly so it knows where it is pointing when it is turned on.

There are three ways to align your telescope: one-, two- and three-star

alignment.

Step 1: To start the alignment, press the centre key (5) on the handbox

and select the first menu option, 'Telescope Align'. There you will be

able to choose between one-, two- and three-star alignment.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bresser 4701170 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info