Bedienungsanleitung Bresser 70-20000 Connect Set (Seite 23 von 72) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

632904

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

• 4. Status of the gateway (after power on)

Green LED:

• Continuous ﬂashing for about 30 seconds: scanning for installed sensors or registering new sensors

• Always lit up and ﬂashing once every 30 seconds: normal operation (receiving sensor data)

• Continuous ﬂashing for a long time or not lit up for a long time: abnormal behavior

Red LED:

• Light up for around 3 seconds: system start-up

• Always off: App is not running or remote access is not yet activated. Otherwise abnormal.

• Flashing every 5 seconds: LAN cable is not properly connected to the gateway and/or an IP address has not been as-

signed to the gateway (no connection to the internet). Check the cable connection and whether DHCP is set in router

conﬁguration (please refer to the router user manual on how to check).

• Always lit up: App is running and/or remote access is activated. Otherwise abnormal

• 5. Firmware upgrade

When starting to run the app, there will be a pop-up message asking for a ﬁrmware upgrade if either one or both of the

gateway ﬁrmware versions are found outdated. There are two ﬁrmware – device ﬁrmware (router-gateway) and RF ﬁrmware

(gateway-sensors) and the upgrade has to be done one after the other separately. After upgrade, the system may become idle

for several minutes and then reboot automatically (the red and green LEDs will ﬂash). If the automatic reboot fails (either one

or both LEDs do not ﬂash after several minutes), please manually power off and then power on the gateway, and wait several

minutes for reboot. To check whether the upgrade has been successful, press the ‘i’ icon on the top left corner to see the

ﬁrmware version numbers.

Soil moisture sensor

• 1. Soil sensor does not increase moisture level immediately after watering:

Cause: Soil moisture sensing cycle is 10 minutes

Solution: Wait for up to 10 minutes until the next cycle of soil moisture sensing has updated the moisture level displayed after

watering. If the sensor is inserted deeply into the soil, wait for some more time to allow for water to diffuse through the covering

soil.

• 2. Soil moisture reading shows lower level than expected

Cause #1: Soil texture may affect the measurement result

Solution: Avoid using soil sensor in soil with extreme texture (too much sand or clay), or adjust the meaning of the levels ac-

cording to the observed soil moisture conditions

Cause #2: Some air space is hidden inside the soil

Solution: Remove and insert again the sensor in another position of soil.

Cause #3: Sensor probe is not inserted deep enough into the soil.

Solution: Push the probe down until the soil moisture sensor (or soil temperature sensor) reaches the root (or seedbed) level

or about two thirds of the depth of the pot. Never insert the sensor deeper than the maximum indicated in ﬁg. 7 (A).

Cause #4: The metal pins of the sensor probe are oxidized or coated with dirt

Solution: Slightly polish the surface of the metal pins (Fig. 7, B).

Router compatibility

Please visit the link below for details of router compatibility

http://iConnect.netinfostation.com

Any conventional router for home networking applications that is allowing network devices to connect to it should be able to

work with the gateway.

Check the user manual and FAQ of your router model, or ask the router manufacturer to ﬁnd out if inter-device communication

is enabled by default.

Technical Speciﬁcation

System requirements:

• iOS version 4.3 or above (iPhone 3GS or above; iPod touch 4th generation or above; iPad)

• Android version 2.3.3 or above (Android phone with a display resolution of 320 x 480 pixels or above)

• Wireless WiFi router that supports inter-communication between the devices that are connected to different ports of the

router.

• Internet connection

• Mobile internet connection for remote access of the BRESSER Connect if outside of the WiFi connection area

(Please visit http://iConnect.netinfostation.com or “Router Compatibility” section for more details of the Smartphone com-

patibility)

Note: Due to variations in the Internet protocol implementation, some Android devices that meet the above requirements,

can still cause problems while running the app.

(Please visit http://iConnect.netinfostation.com for more details of the Smartphone compatibility)

Garantie

Warranty

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bresser 70-20000 Connect Set Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info