Bedienungsanleitung Bresser 7000024 ClimaTemp Hygro DLX (Seite 8 von 24) (Deutsch, Englisch)

785359

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

8 / 24

17 Selected channel of the wireless sensor 18 Outdoor temperature (wireless sensor)

19 Outdoor humidity (wireless sensor)

6 Before starting operation

NOTICE

Avoid connectivity disruptions!

To avoid connectivity disruptions between the devices, consider the following points before starting

operation.

1. Place base station (receiver) and remote sensor (sender) together as close as possible.

2. Set up power supply for the base station and wait until the indoor temperature is displayed.

3. Set up power supply for the remote sensor.

4. Position the base station and the remote sensor within the effective transmission range.

5. Ensure that the base station and remote sensor are assigned to the same channel.

When changing batteries always change batteries in the main unit as well as all remote units and re-

place them in the correct order, so the remote connection can be re-established. If either of the

devices is mains-powered, the power supply must be disconnected for a short moment also for this

device when exchanging the batteries. If batteries are exchanged in only one of the devices (i.e. the

remote sensor) the signal can’t be received or can’t be received correctly.

Note, that the effective range is vastly affected by building materials and position of the main and re-

mote units. Due to external influences (various RC devices and other sources of interference), the

maximum distance can be greatly reduced. In such cases we suggest to position the main unit and the

remote sensor at other places. Sometimes all it takes is a relocation of one of these components of a

few inches!

7 Setting up power supply

Base station

1. Remove the battery compartment cover.

2. Insert the batteries into the battery compartment. Ensure that the battery polarity (+/-) is correct.

3. Replace the battery compartment cover.

4. Wait until the indoor temperature is displayed on the base station.

NOTICE!Alternatively, operation with mains power supply (DC 5V) is possible. Proceed as fol-

lows:

5. Insert the DC connector into the connection socket of the base station.

6. Insert the mains plug into the power outlet.

7. The device is energized directly.

8. Wait until the indoor temperature is displayed on the base station.

NOTICE!When switching from mains power supply to battery power supply or vice versa,

the power supply is being disabled for a short moment for technical reasons. In this process

all settings made previously, will be deleted.

Remote sensor

9. Loosen the screws at the battery compartment cover with a small Philips screwdriver and remove

the cover.

10. Insert the batteries into the battery compartment. Ensure that the battery polarity (+/-) is correct.

11. Set the channel selector switch to the desired channel.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bresser 7000024 ClimaTemp Hygro DLX Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bresser 7000024 ClimaTemp Hygro DLX

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info