Bedienungsanleitung Bresser 7001040 - WIFI 4Cast (Seite 26 von 56) (Deutsch, Englisch, Französisch)

771286

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

26 / 56

7 Outdoor temperature (°C/°F adjustable

globally)

8 Outdoor humidity (RH in %)

9 Battery level indicator (base station) 10 Outdoor sensor channel with symbol for

enabled wireless connection

11 ‘Feels like’ temperature 12 Air pressure (hPa/mb)

13 Wind direction 14 Wind speed (km/h or mp/h adjustable)

15 Display of weekday, temperature values

and general weather forecast for the fifth

day

16 Battery level indicator (outdoor sensor)

17 Indoor humidity (RH in %) 18 Display of weekday, temperature values

and general weather forecast for the

fourth day

19 Indoor temperature (°C/°F adjustable glob-

ally)

20 Display of weekday, temperature values

and general weather forecast for the third

day

21 General weather forecast for the second /

next day

22 Daily minimum temperature (°C/°F ad-

justable globally) for the second/next day

23 Daily maximum temperature (°C/°F ad-

justable globally) for the second / next day

24 Weekday display for the second / next day

25 General weather forecast for the current

day

*if several sensors are connected (optional, not included)

7 Before commissioning

NOTICE

Avoid connection faults!

In order to avoid connection problems between the devices, the following points must be observed

during commissioning.

1. Place the base unit (receiver) and sensor (transmitter) as close together as possible.

2. Connect the power supply to the base unit and wait until the indoor temperature is displayed.

3. Establish power supply for the sensor.

4. Set up/operate the base unit and sensor within the effective transmission range.

5. Make sure that the base unit and the radio sensor are set to the same channel.

When changing the batteries, always remove the batteries in both the base unit and the sensor and

reinsert them in the correct order so that the radio connection can be re-established. If one of the two

devices is operated via a mains power connection, the power connection for this device must also be

disconnected briefly when changing the battery. If, for example, only the batteries in the sensor are re-

placed, the signal cannot be received or can no longer be received correctly.

Note that the actual range depends on the building materials used in the building and the position of

the base unit and outdoor sensor. External influences (various radio transmitters and other sources of

interference) can greatly reduce the possible range. In such cases, we recommend finding other loca-

tions for both the base unit and the outdoor sensor. Sometimes a shift of just a few centimetres is

enough!

8 Setting up power supply

Base device

1. Put the DC connector into the connection socket of the base station.

2. Put the mains plug into the power outlet.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bresser 7001040 - WIFI 4Cast Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bresser 7001040 - WIFI 4Cast

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info