Bedienungsanleitung Bresser 7003220 (Seite 74 von 80) (Deutsch, Englisch)

784734

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

7. The console will stay in AP mode for you to check the rmware version and all the current

setting. Simply press and hold [ SENSOR / WI-FI ] key for 6 seconds to exit AP mode.

IMPORTANT NOTE:

- Please keep connecting the power during the rmware update process.

- Please make sure your PC/Mac's WI-FI connection is stable.

- When the update process start, do not operate the PC/Mac and console until the update nished.

- During rmware update the console will stop upload data to the cloud server. It will reconnect to your WI-FI

router and upload the data again once the rmware update succeed. If the console cannot connect to your

router, please enter the SETUP page to setup again.

- After the rmware update, If the setup informations are missing, please input the setup information again.

- Firmware update process have potential risk, which cannot guarantee 100% success. If the update fail,

please redo the above step to update again.

8.2 BATTERY REPLACEMENT

When low battery indicator or is

displayed near the antenna icon of

the sensor(s), it indicates that the

outdoor 7-IN-1 sensor and/or current

channel sensor(s) battery power is low

respectively. Please replace with new

batteries.

8.2.1 RE-PAIRING THE SENSOR(S) MANUALLY

Whenever you changed the batteries of the 7-in-1 weather sensor array or other additional

sensors, re-synchronization must be done manually.

1. Change all the batteries to new ones in the low battery sensor(s).

2. Press [ SENSOR / WI-FI ] key on the console to enter sensor synchronization mode (as

indicated by the ashing antenna ).

8.3 RESET AND FACTORY RESET

To reset the console and start again, press the [ RESET ] key once or remove the backup battery

and then unplug the adapter.

To resume factory settings and remove all data, press and hold the [ RESET ] key for 6 seconds.

8.4 WIRELESS 7-IN-1 SENSOR ARRAY MAINTENANCE

REPLACE THE WIND VANE

Unscrew and remove the wind

vane for replacement

REPLACE THE WIND CUP

1. Unscrew and remove the

top cap

2. Remove the wind cup for

replacement

CLEANING THE THERMO-

HYGRO SENSOR

Remove the 2 screws at the

bottom of the radiation shield.

Gently pull out the shield.

5. Carefully remove any dirt or

insects on the sensor (do not let

the sensors inside get wet).

Clean the shield with water to

remove any dirt or insects.

7. Install all the parts back when

they are clean and fully dried.

CLEANING THE RAIN COLLECTOR

1. Rotate the rain collector by turning it

30°anti-clockwise.

2. Gently remove the rain collector.

3. Clean and remove any debris or

insects.

4. Install the collector when it is clean

and fully dried.

CLEANING THE UV SENSOR AND

CALIBRATION

• For precision UV measurement,

gentle clean the UV sensor cover

lens with damp micro-ber cloth.

• Over time, the UV sensor will

naturally degrade. The UV sensor

can be calibrated with a utility grade

UV meter, please refer to Calibration

section in previous page for about

the UV sensor calibration.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bresser 7003220 Seite 74

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bresser 7003220

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info