Bedienungsanleitung Bresser 7007900 Meteo THBM Colour (Seite 8 von 20) (Englisch)

729927

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

8 / 20

3 Humidity value (outdoor) 4 Climate indicator (outdoor) (too cold, optimal,

too warm)

5 Dew point 6 Heat index

7 Barometric pressure (hPa, inHg or mmHg) 8 Graphical weather trend display

9 Moon phase 10 Symbol for highest (MAX) or lowest (MIN)

value

11 Humidity trend (indoor) (rising, steady or fall-

ing)

12 Indoor humidity value

13 Climate indicator (indoor) (too cold, optimal,

too warm)

14 Symbol indoor area

15 Alarm symbol for high (HIGH) or low (LOW)

humidity

16 Temperature value (indoor)

17 Temperature unit (°C or °F selectable) 18 Temperature trend (indoor) (rising, steady or

falling)

19 Daylight saving time (DST) 20 Alarm symbol (bell)

21 Alarm symbol for high (HIGH) or low (LOW)

temperature (indoor)

22 Symbol for radio signal

23 Battery level indicator 24 Month (M)

25 Current time (seconds) 26 Day (D)

27 Current time (minutes) 28 Current time (hours)

29 Weekday 30 AM/PM information in 12-hour time mode

31 Alarm symbol for high (HIGH) or low (LOW)

temperature (outdoor)

32 Temperature value (outdoor)

33 Temperature trend (outdoor) (rising, steady or

falling)

34 Ice warning

35 Alarm symbol for high (HIGH) or low (LOW)

humidity (outdoor)

36 Symbol outdoor area with channel display

7 Before starting operation

NOTICE

Avoid connectivity disruptions!

To avoid connectivity disruptions between the devices, consider the following points before starting

operation.

1. Place base station (receiver) and remote sensor (sender) together as close as possible.

2. Set up power supply for the base station and wait until the indoor temperature is displayed.

3. Set up power supply for the remote sensor.

4. Position the base station and the remote sensor within the effective transmission range.

5. Ensure that the base station and remote sensor are assigned to the same channel.

When changing batteries always change batteries in the main unit as well as all remote units and re-

place them in the correct order, so the remote connection can be re-established. If either of the

devices is mains-powered, the power supply must be disconnected for a short moment also for this

device when exchanging the batteries. If batteries are exchanged in only one of the devices (i.e. the

remote sensor) the signal can’t be received or can’t be received correctly.

Note, that the effective range is vastly affected by building materials and position of the main and re-

mote units. Due to external influences (various RC devices and other sources of interference), the

maximum distance can be greatly reduced. In such cases we suggest to position the main unit and the

remote sensor at other places. Sometimes all it takes is a relocation of one of these components of a

few inches! Though the remote unit is weather proof, it should be placed away from direct sunlight,

rain or snow.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bresser 7007900 Meteo THBM Colour Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bresser 7007900 Meteo THBM Colour

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info