Bedienungsanleitung Bresser 7060200 - TemeoTrend FSX (Seite 9 von 16) (Englisch)

729860

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

9 / 16

8 Battery level indicator

1. When the batteries in the base station or in the remote sensor reach the low charge level, the cor-

responding battery level indicator appears on the display.

2. When replacing a set of batteries, always also remove the batteries from the other part of the

device and reinsert the batteries in the intended order (see chapter "Setting up power supply").

Replace the batteries in the relevant part of the device with a completely new set with full capacity.

This ensures that the connection between the devices is reestablished correctly.

9 Automatic time setting

After the power supply was established, the clock will automatically search for the radio signal. This

will take approximately 3 to 8 minutes to finish this process.

If the radio signal is received correctly, the date and time will be set automatically and the radio control

signal icon turns on.

If the clock fails to receive the time signal, go ahead with the following steps:

1. Press °C/°F button on the base station for approx. 3 seconds to initate RC signal reception again.

2. If the device is still not receiving the signal, the time must be set manually.

Read the detailed manual for more information about manual time and alarm setting (see download in-

formation on page 2).

10 Manual time setting and other user defined

settings

1. In normal display mode, press MODE/SET button for approx. 3 seconds to switch to settings

mode.

2. Digits to be set are flashing.

3. Press DOWN/RAIN HISTORY button or UP/RCC/ALARM button to change the value.

4. Press the MODE/SET button to confirm the setting and move to the next setting.

5. Settings order: 12/24 hours mode > RCC on/off > time zone (-12 to +12 hours) > hours > minutes

> seconds > year > month > day > language > temperature unit > barometric pressure unit > wind

speed unit > precipitation unit > wind direction

6. Finally press MODE/SET button to save the settings and exit settings mode.

11 Alarm settings

1. In normal display mode, press the TIME button several times to display the Alarm time AL1 or

AL2.

2. Press ALARM button for approx. 3 seconds to enter the alarm time setting mode.

3. Digits to be set are flashing.

4. Press CH/UP or 12/24/DOWN button to change the value.

5. Press ALARM button to confirm and continue to the next setting.

6. Settings order: hours > minutes > ice alert on/off

NOTICE!If ice alert is enabled (on), the alarm will sound 30 seconds before the set alarm time if

the temperature is -3° or below.

7. Finally press the ALARM button to save the settings and exit the setting mode. Alarm will be activ-

ated automatically. The symbol will be displayed.

8. In normal display mode, press the ALARM button several times to enable alarm time AL1, AL2 or

both. If the alarm is enabled, the corresponding symbol will be displayed ( 1, 2 or 1 2).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bresser 7060200 - TemeoTrend FSX Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bresser 7060200 - TemeoTrend FSX

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info